17 July 2018 in IEEE Transactions on Industry Applications
High speed PMSM are used in electric vehicles because of their intense power density. The high speed implies a significant electromotive force and requires flux weakening. The usual control algorithms realize flux weakening by adding a negative Id current component when the voltage required by the current regulation exceeds the maximum voltage depending on the battery. If the magnet can be totally defluxed then it is better to use a Maximum Torque Per Volt (MTPV) strategy. Furthermore, there is no speed regulation in the control and the driver gives a torque reference. This reference value has to be limited by the attainable operating points therefore the battery power limit has to be taken into account in addition to the voltage and current limits. The d-q current references are calculated to minimize the total current magnitude required to reach the reference torque. This paper proposes a strategy to control a PMSM operating continuously since the speed zero up to the maximum speed without switching algorithm, in order to take into account the different limitations (current, voltage, power) and to expand the over-speed zone. In order to validate the proposed strategy, experimental results are shown for a low power machine.
17 November 2020 in IEEE Transactions on Power Electronics
Making electrical driving systems cheaper, lighter, and more reliable is the consistent pursuit of current research and development. Mono-Inverter Multi-Permanent Magnet Synchronous Motor systems tend to share the static converters in electro-mechanical systems by connecting machines in parallel. This type of system has an obvious advantage in overall weight and cost. In this paper, we have proposed a new Maximum Torque Per Ampere (MTPA) control strategy for a MIMPMSM system, which supports three or more machines in parallel and works both in motor mode and brake mode. The calculation of the MTPA point minimizing the overall joule loss of the system is also given. The synchronization condition, stability, and optimal efficiency of the system are strictly proven. This new control structure is simple making current single PMSM systems easy to upgrade to support the MIMPMSM system. The experiment has demonstrated its feasibility, stability, and improvements in efficiency.
1 November 2017 in IEEE Transactions on Industry Applications
Current research and development programs in aviation are promoting new technological advances to make electrical systems cheaper, lighter and more reliable. Mono-Inverter Dual-Permanent Magnet Synchronous Motor (MIDPMSM) systems tend to share the static converters in electro-mechanical systems by connecting motors in parallel. However several studies have shown that the efficiency of this configuration is lower than those with a traditional Mono-Inverter Mono-PMSM configuration, especially when unequal load torques are applied. In this paper, we propose an efficiency-optimized control method for MIDPMSM systems which has been designed using rigorous, mathematical calculations. The determinacy, stability, and optimal efficiency of the system, which are essential in an aviation application, are explained in detail. This new control structure is simple making current single PMSM systems easy to upgrade to support the MIDPMSM system. The experiment has demonstrated not only feasibility but also significant improvements in performance.
22 August 2022 in IEEE Transactions on Power Delivery
The modular multilevel converter (MMC) has been widely adopted in different applications, such as high-voltage direct current (HVDC), electric drives and static synchronous compensators. Despite the application, MMC realization requires a high number of power electronic components, sensors, and communication cables. This paper proposes a sliding-mode observer for capacitor voltages of the MMC, using the measurements of arm currents and arm voltages. A linear corrector within the hysteresis band is proposed to reduce the chattering in the observer dynamics. Moreover, guidelines for tuning the observer gain are presented. The SM capacitance value is included as a parameter uncertainty of the observer. The proposal reduces the requirements of voltage sensors and optical links in MMC and allows fault-tolerant operation. The proposed observer performance is evaluated through a simulation of 100 MVA three-phase MMC-HVDC during initialization, steady-state, and submodule failures. The effect of the switching and sampling frequencies on the observer performance is also evaluated. Finally, experimental results validate the proposal in a downscale 3 kVA single-phase MMC prototype.
8 February 2021 in IEEE Access
Connecting two PMSMs in parallel to a 2-level 3-leg inverter gives a way to build up a high power-density driving system using existing electronic devices. But this type of system has a nature of nonlinearity that creates an obstacle in high performance control and the original system cannot be feedback-linearized directly. This article presents a reduced-order feedback-linearization method. In the first place, an extra order-reducing step that separates the system as a main system and an auxiliary system is applied. Then a feedback-linearization method is applied to the reduced-order system. With these effort, the original system can be converted into a linear time-invariant system bringing the controller design problem into the linear domain. In the last step, a linear robust state-feedback controller is used to achieve the speed control as well as compensate the unmeasurable external load torque. An extensive experiment is given to verify the feasibility and good performance in a highly unbalanced load torque situation of the designed controller.