28 July 2023 in Frontiers in Materials
SPSivasubramanian Palanisamy
Sivasubramanian Palanisamy
The optimization of heat transfer in heat exchanging equipment is paramount for the efficient management of energy resources in both industrial and residential settings. In pursuit of this goal, this empirical study embarked on enhancing the heat transfer performance of a double pipe heat exchanger (DPHX) by introducing silver (Ag)-graphene oxide (GO) hybrid nanofluids into the annulus of the heat exchanger. To achieve this, three distinct molar concentrations of Ag ornamented GO hybrid nanoparticles were synthesized by blending GO nanoparticles with silver nitrate at molarities of 0.03 M, 0.06 M, and 0.09 M. These Ag-GO hybrid nanoparticles were then dispersed in the base fluid, resulting in the formation of three distinct hybrid nanofluids, each with a consistent weight percentage of 0.05 wt%. Thorough characterization and evaluation of thermophysical properties were performed on the resulting hybrid nanomaterials and nanofluids, respectively. Remarkably, the most significant enhancement in heat transfer coefficient, Nusselt number, and thermal performance index (62.9%, 33.55%, and 1.29, respectively) was observed with the 0.09 M Ag-GO hybrid nanofluid, operating at a Reynolds number of 1,451 and a flow rate of 47 g/s. These findings highlight the substantial improvement in thermophysical properties of the base fluid and the intensification of heat transfer in the DPHX with increasing Ag molarity over GO. In summary, this study emphasizes the vital importance of optimizing the molarity of the material, which also plays a significant role in nanoparticle synthesis to achieve the optimal amplification of heat transfer.
25 January 2019 in International Journal of Ambient Energy
Influence on thermal performances of the concentric tube shell assisted heat-pipe heat exchanger with and without adiabatic section has been experimentally investigated. Water is used as heat-carrying fluid and methanol is used as working fluid in the heat pipe.Mass flow rates of hot water ranges from 30 lph to 70 lph, for cold water 15 lph to 35 lph and during the investigation the temperature of the hot water at inlet is ranges 50°C to 60°C. For various mass flow rate and inlet temperature the heat transfer coefficient, heat transfer rate and effectiveness of the heat exchanger are reported. The mass flow rate of hot and cold water is 70lph and 35lph and inlet hot water at 60°C, the effectiveness of heat pipe without adiabatic section is 26.9%.The investigation reveals that there is an increase in effectiveness by 11.2% is obtained in without adiabatic section, compared to with adiabatic section.
8 February 2018 in International Journal of Ambient Energy
In this work, CuO-water nanofluid with an average size of nanoparticles (24 nm) and volume concentrations of 0.1% and 0.5% is used. For the computer microprocessor cooling, an aluminium minichannel of dimension (40 × 1 × 3) mm3 is fabricated instead of an aluminium heat sink and a cooling fan. It is shown that the dispersion of nanoparticles into the distilled water has produced a considerable enhancement of the cooling of the minichannel. Experiments were conducted for Reynolds number ranging from 25 to 800 under a laminar regime. From the experiments, it is found that better heat transfer is achieved when CuO-water nanofluid is used as the working fluid.
5 February 2015 in Arabian Journal for Science and Engineering
3 October 2016 in Arabian Journal for Science and Engineering
1 August 2019 in Journal of Physics: Conference Series
KSKrishna Bhagavathi Sankar
Krishna Bhagavathi Sankar
The paper describes the modeling and analysis of a Sport Utility Vehicle (SUV). The present study mainly focuses on the reduction of aerodynamics drag and lift coefficient of a car, which helps to improve the vehicle performance and fuel efficiency. Usually the aerodynamic drag and lift is insignificant at low vehicle speed but the magnitude of air resistance becomes considerable with accelerating the vehicle. The Computational Fluid Dynamics (CFD) helps to analyze the flow stream around a SUV. The modeling software is used to design a 3D car model and the flow stream is analyzed by ANSYS Fluent. Initially, the first model was analyzed at various velocity conditions using Reynolds-Averaged Navier–Stokes (RANS) with standard k-ε model. The basic model of SUV has a drag coefficient and lift coefficient value of 0.62 and 0.099 respectively. Initially the first model is designed by introducing air splitter on roof and based on the results the second model is designed by introducing 15 degree boat tailing angle with first model. The drag reduction is reduced by 6.45% for first model and 19.35% for second model compared to the base model. Similarly, the lift coefficient is reduced by 2.02% for first model and 30.30% for the second model. Moreover the second model produces low drag and lift coefficient than first and base model. A significant reduction is observed in first model when compared to the base model. The vector plots are used to examine the streamline path of both the models.