This paper describes the implementation of a three-dimensional (3D) concrete constitutive model for fiber-based analysis of RC members subjected to combined loadings including torsion. The proposed model is formulated to address the interaction between the axial force, bidirectional shear, biaxial bending, and torsion. The shear mechanism along the beam is modeled using a Timoshenko beam approach with 3D frame elements with arbitrary cross-sectional geometry. The model considers the 3D equilibrium, compatibility, and constitutive laws of materials at the section and structural level. The concrete constitutive law follows the softened membrane model with a tangent-stiffness formulation. The emphasis of the paper is on evaluation of the effect of the different stress states on the global and local behavior of the member. The ability of the model to assess the ultimate strength, stiffness, energy dissipation, failure modes under 3D loading is evaluated by correlation of analytical results with experi...
Seismic code provisions in several countries have recently adopted the new concept of performance-based design. New analysis procedures have been developed to estimate seismic demands for performance evaluation. Most of these procedures are based on simple material models though, and do not take into account degradation effects, a major factor influencing structural behavior under earthquake excitations. More importantly, most of these models cannot predict collapse of structures under seismic loads. This study presents a newly developed model that incorporates degradation effects into seismic analysis of structures. A new energy-based approach is used to define several types of degradation effects. The model also permits collapse prediction of structures under seismic excitations. The model was used to conduct extensive statistical dynamic analysis of different structural systems subjected to a large ensemble of recent earthquake records. The results were used to propose approximate methods for estimatin...
This paper presents a nonlinear model for pretensioned prestressed concrete girders. The model consists of three main components: a beam-column element that describes the behavior of concrete, a truss element that describes the behavior of prestressing tendons, and a bond element that describes the transfer of stresses between the prestressing tendons and the concrete. The model is based on a two-field mixed formulation, where forces and deformations are both approximated within the element. The nonlinear response of the concrete and tendon components is based on the section discretization into fibers with uniaxial hysteretic material models. The stress transfer mechanism is modeled with a distributed interface element with special bond stress-slip relation. A method for accurately simulating the prestressing operation is presented. Accordingly, a complete nonlinear analysis is performed at the different stages of prestressing. Correlation studies of the proposed model with experimental results of pretens...
1 December 2011 in Journal of Composites for Construction
Nonlinear finite-element (FE) analysis was carried out to investigate the structural response of prestressed concrete (PC) beams strengthened with fiber reinforced polymer (FRP) composites in shear. Development of the FE model for concrete structures dominated by shear, in particular for FRP-strengthened concrete structures, requires careful consideration in choosing the appropriate elements and constitutive laws to simulate the proper failure mode. The paper presents a new three-dimensional technique to model FRP-strengthened prestressed concrete beams. Most previous work has dealt with two-dimensional analysis of FRP-strengthened reinforced concrete beams. The novel attributes of the proposed model lie in the description of the three-dimensional constitutive material models for each component. The model accounts for the softening behavior of concrete under a triaxial state of stress. A new three-dimensional interface element necessary to capture the debonding failure was proposed. In particular, the effect of the out of plane stress behavior of the FRP-concrete interface, which is currently unavailable through experimental measurements, was carefully evaluated. The use of mechanical anchors to improve the bond behavior was properly simulated. In addition, the prestressing operation and precracking effects were also simulated in the model through a phased analysis technique, which makes it possible to predict the response with respect to the time-dependent behavior of elements and materials. The FE model developed in this study was calibrated through comparison with test results. This paper reports not only on the fundamental investigation of the strengthening effect of FRP composites for PC beams but also on the identification of the damage mechanisms and the progression of failure. The model was shown to provide a good level of correlation with experimental data, and could therefore be used to conduct extensive parameter studies.
The contribution presents novel observations on unreinforced masonry made of solid clay brick units and surrounding mortar joints. Focus is the brittle-ductile interaction of the two constituents in form of the so-called masonry prism test under axial compression. The experimental observations include Digital Image Correlation (DIC) data from a newly acquired 3-D DIC system to ascertain the effect of bond on the overall behaviour of the masonry composite. Special attention is directed towards the use of the DIC system to observe mismatch among the two constituents leading to tensile splitting under axial compression. Preliminary tests were performed on the brick units and mortar cubes aside from the masonry prisms using the 3-D DIC system for imaging which did display interesting results which would have been missed by traditional deformation measurements. The presentation concludes with remark on the resolution and limitations of the DIC system.
Posttensioning is an effective method for the construction of different types of bridge girders such as those used in segmentally erected bridges. Available nonlinear analysis programs for bridge girders under severe loading conditions are computationally expensive though. In addition, they neglect important phenomena such as bond-slip, friction, and anchorage losses. The objective of the proposed work is to develop a new nonlinear finite-element program for analysis of posttensioned bridge girders. The new model overcomes most of the difficulties associated with existing models. The model is based on the computationally efficient mixed formulation and considers bond, friction, and anchorage loss effects. The mixed formulation is characterized by its fast convergence, usually with very few finite elements and its robustness even under severe loading conditions. The posttensioning operation is accurately simulated using a phased-analysis technique, in which each stage of the posttensioning operation is simulated through a complete nonlinear analysis procedure. Correlation studies of the proposed model with experimental results of posttensioned specimens are conducted. These studies confirmed the accuracy and efficiency of the newly developed software program, which represents an advancement over existing commercial software packages for evaluating posttensioned bridge girders, in particular those subjected to severe loading conditions.