Abdeldjelil Belarbi

Abdeldjelil Belarbi

Auto-generated profile, based on publicly available information

Abdeldjelil Belarbi

University of Houston

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2012 in Journal of Composites for Construction
Verified
Journal Article
Closed access
ABAbdeldjelil Belarbi
Abdeldjelil Belarbi
HWHuanzi Wang
Huanzi Wang
A research program was initiated to develop a nonferrous reinforcement system for concrete bridge decks using continuous fiber-reinforced polymer (FRP) bars and discrete, randomly distributed polypropylene fibers. This hybrid system may eliminate problems related to corrosion of steel reinforcement while providing requisite strength, stiffness, and desired ductility, which are shortcomings of the FRP reinforcing system in plain concrete. This paper presents the results of a part of this research program [i.e., the long-term bond behaviors of this FRP/fiber-reinforced concrete (FRC) hybrid system]. Bond durability for the FRP/plain concrete system that served as a reference is also reported. Test results indicated that ultimate and design bond strength experienced noticeable degradation when exposed to combined environmental conditioning, including freeze-thaw cycles, high temperature (60°C), and deicing salt solution. Test results showed that bond durability significantly improved owing to the res...

1 September 2013 in Journal of Bridge Engineering
Verified
Journal Article
Closed access
SBSang-Wook Bae
Sang-Wook Bae
ABAbdeldjelil Belarbi
Abdeldjelil Belarbi
Efforts to prevent the debonding failure mode of externally bonded fiber-reinforced polymer (FRP) strengthening systems have led to the investigation of many different kinds of anchorage systems. An effective anchorage system allows externally bonded FRP reinforcements to continue carrying load, even after debonding occurs. In this study, an experimental program was performed on six full-scale RC T-beams strengthened in shear using externally bonded carbon FRP sheets with three different anchorage systems, the so-called (1) discontinuous mechanical anchorage (DMA) system, (2) sandwich discontinuous mechanical anchorage (SDMA) system, and (3) additional horizontal strips (HS) system. The experimental results showed that the SDMA system performed best, followed by the DMA and HS systems. The RC T-beams strengthened with the SDMA system showed a 59–91% increase in shear strength, altering the failure mode from FRP debonding to FRP rupture. In addition, the shear contribution of internal transverse st...

1 February 2013 in Journal of Composites for Construction
Verified
Journal Article
Closed access
Ayman OkeilAyman Okeil
Ayman Okeil
ABAbdeldjelil Belarbi
Abdeldjelil Belarbi
DKDaniel A. Kuchma
Daniel A. Kuchma
This paper presents the results from an investigation into the reliability of reinforced concrete bridge girders strengthened in shear using fiber-reinforced polymers (FRP). Two expressions for the shear design of FRP-strengthened girders were developed as part of a National Cooperative Highway Research Program project. The expressions were developed for two distinct cases, namely, bonded and anchored FRP reinforcement. Uncertainties inherent in the new design models were first assessed using an extensive database of hundreds of experimentally tested specimens. Variabilities in material, fabrication tolerances, dead and live loads, and distribution factors obtained from the literature were then included in a limit state function for the shear strength mode of failure. The reliability of a representative design space comprising 18 bridge girders that cover different span lengths, shear deficiency levels, and girder location (exterior versus interior) was calculated for both bonded and anchored stre...

1 February 2013 in Journal of Bridge Engineering
Verified
Journal Article
Closed access
SBSang-Wook Bae
Sang-Wook Bae
MMMichael Murphy
Michael Murphy
AMAmir Mirmiran
Amir Mirmiran
ABAbdeldjelil Belarbi
Abdeldjelil Belarbi
This study investigated the shear performance of an RC beam strengthened in shear with externally bonded carbon fiber-reinforced polymer (CFRP) strips, subjected to a cyclic loading for 2 million cycles at 1 Hz. The stress level in the stirrups caused by the cyclic loading used in this study was higher than those typically used in fatigue studies, which could have caused the yielding of some stirrups from the beginning of cyclic loading. This was done to reflect the fact that many RC beams in need of shear strengthening do not meet the minimum stirrup requirement for the new and increased shear demand. The experimental results obtained in this study and a comprehensive review of the existing literature showed that RC beams strengthened in shear with externally bonded CFRP could survive 2 million cycles of cyclic loading without failure. Furthermore, the residual shear strength of the FRP-strengthened beam appeared to be greater, albeit slightly, than the static shear strength of the unstrengthened control beam. This study’s results also suggested that limiting the interfacial stress in CFRP strips to less than 1.5 MPa or 25% of its ultimate interfacial strength would increase fatigue life by avoiding debonding of CFRP strips.

1 April 2013 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
QLQian Li
Qian Li
ABAbdeldjelil Belarbi
Abdeldjelil Belarbi
Reinforced Concrete (RC) bridge columns can be subjected to combined flexure, shear, axial and torsional loadings under multidirectional earthquake motions and significant vertical motions, specifically in skewed and curved bridges, bridges with specific structural restraints, and bridges with unequal spans or column heights. This paper presents experimental and analytical studies to assess the damage progression of square RC bridge columns under combined loadings including torsion. The main variable in this study is the ratio of Torsional-to-bending Moments (T/M). The effects of combined loadings on the torsional and flexural hysteretic responses, strength, plastic hinge distribution, and progression of damage states are highlighted in this paper. A unified equivalent damage index model is proposed to couple the flexural and torsional actions for combined loadings. Quantified damage indices value under combined loadings can be correlated to the categorized damage states from a performance-based point of view. Based on the experimental and analytical results, the progression of damage was found to be amplified by the torsion effect, and the rotational ductility was decreased due to the effect of combined loadings.

1 December 2011 in Journal of Composites for Construction
Verified
Journal Article
Closed access
YYYoung-Min You
Young-Min You
AAAshraf Ayoub
Ashraf Ayoub
ABAbdeldjelil Belarbi
Abdeldjelil Belarbi
Nonlinear finite-element (FE) analysis was carried out to investigate the structural response of prestressed concrete (PC) beams strengthened with fiber reinforced polymer (FRP) composites in shear. Development of the FE model for concrete structures dominated by shear, in particular for FRP-strengthened concrete structures, requires careful consideration in choosing the appropriate elements and constitutive laws to simulate the proper failure mode. The paper presents a new three-dimensional technique to model FRP-strengthened prestressed concrete beams. Most previous work has dealt with two-dimensional analysis of FRP-strengthened reinforced concrete beams. The novel attributes of the proposed model lie in the description of the three-dimensional constitutive material models for each component. The model accounts for the softening behavior of concrete under a triaxial state of stress. A new three-dimensional interface element necessary to capture the debonding failure was proposed. In particular, the effect of the out of plane stress behavior of the FRP-concrete interface, which is currently unavailable through experimental measurements, was carefully evaluated. The use of mechanical anchors to improve the bond behavior was properly simulated. In addition, the prestressing operation and precracking effects were also simulated in the model through a phased analysis technique, which makes it possible to predict the response with respect to the time-dependent behavior of elements and materials. The FE model developed in this study was calibrated through comparison with test results. This paper reports not only on the fundamental investigation of the strengthening effect of FRP composites for PC beams but also on the identification of the damage mechanisms and the progression of failure. The model was shown to provide a good level of correlation with experimental data, and could therefore be used to conduct extensive parameter studies.