Nataliia Meranova

Nataliia Meranova

Auto-generated profile, based on publicly available information

Nataliia Meranova

Institute of Engineering Thermophysics of the National Academy of Sciences of Ukraine

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 August 2021 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
NFNataliia Fialko
Nataliia Fialko
RDRoman Dinzhos
Roman Dinzhos
JSJulii Sherenkovskii
Julii Sherenkovskii
NMNataliia Meranova
Nataliia Meranova
DIDiana Izvorska
Diana Izvorska
NKNeli Koseva
Neli Koseva
This paper reports the experimental study carried out to establish the dependence of the thermal conductivity of polypropylene-based nanocomposites filled with carbon nanotubes on the main parameter of the temperature regime of their manufacturing ‒ the level of overheating a polymer melt relative to its melting point. The study has been conducted for nanocomposites that were manufactured by applying a method based on the mixing of components in the polymer melt applying a special disk extruder. During the composite manufacturing process, the level of melt overheating varied from 10 to 75 K, with the mass share of filler ranging from 0.3 to 10.0 %. It is shown that increasing the overheating of a polymer melt causes an increase in the thermal conductivity of the composites. However, when the overheating has reached a certain value, its further growth does not increase the thermal conductivity of nanocomposites. Based on the established pattern, the rational level of this overheating has been determined. That resolves the tasks of manufacturing highly heat-conducting nanocomposites and implementing appropriate energy-saving technology. Data have been acquired on the effects of the impact of the amount of polymer melt overheating on the values of the first and second percolation thresholds for the examined nanocomposites. It is established that the value of the first percolation threshold is more sensitive to the specified amount of overheating. The dependences of the density of the examined composites on the level of polymer melt overheating have been derived. The correlation between a given dependence and the nature of a corresponding change in the thermal conductivity of the composites has been established. Applying the proposed highly heat-conducting nanocomposites is promising for micro and nanoelectronics, energy, etc.

30 April 2022 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
NFNataliia Fialko
Nataliia Fialko
RDRoman Dinzhos
Roman Dinzhos
JSJulii Sherenkovskii
Julii Sherenkovskii
NMNataliia Meranova
Nataliia Meranova
VPViktor Prokopov
Viktor Prokopov
VMVolodymyr Makhrovskyi
Volodymyr Makhrovskyi
A set of experimental studies has been carried out to establish the effect of the mixing time of components of nanocomposite materials on their thermal conductivity, specific heat, and density. The physical properties of polypropylene-carbon nanotube composites were to be studied. During the experiments, the duration of mixing of the components in the melt of the polymer varied from 5 to 52 minutes, the mass fraction of the filler ‒ in the range of 0.3...10 %, and nanocomposite temperature – from 290 K to 475 K. It was found that an increase in the mixing time of components of nanocomposite materials could lead to a significant (more than 70 times) increase in their thermal conductivity. It is also shown that the influence of the specified time is limited to its value equal to 27 minutes, above which the change in the thermal conductivity of nanocomposites can be neglected. It was found that the sensitivity of the thermal conductivity of nanocomposites to the time of mixing of their components decreases with a decrease in the mass fraction of the filler. Temperature dependences of the specific heat capacity of the studied composites were obtained by varying the mixing time of their components and the mass fraction of the filler. It was found that with an increase in the specified time, there is a decrease in the heat capacity of nanocomposites, which is significantly manifested only in the region of temperatures close to the melting point of the composite matrix. It is shown that the dependence of the density of nanocomposites on the mixing time of their components in qualitative terms is similar to the corresponding dependence for their thermal conductivity. The obtained data can be used to choose the mixing time of components of nanocomposite materials in the development of appropriate technology for their production Виконано комплекс експериментальних досліджень щодо встановлення впливу часу змішування компонентів нанокомпозиційних матеріалів на їхню теплопровідність, питому теплоємність та густину. Дослідженню підлягали фізичні властивості композитів «поліпропілен-вуглецеві нанотрубки». При проведенні експериментів тривалість змішування компонентів у розплаві полімеру змінювалася від 5 до 52 хв, масова частка наповнювача – у діапазоні 0,3…10 % і температура нанокомпозитів – від 290 К до 475 К. Встановлено, що збільшення часу змішування компонентів нанокомпозиційних матеріалів може призводити до суттєвого (більш ніж 70 разів) підвищення їх теплопровідності. Показано також, що вплив зазначеного часу обмежується його значенням 27 хв, при перевищенні якого зміною теплопровідності нанокомпозитів можна знехтувати. Встановлено, що чутливість теплопровідності нанокомпозитів до часу змішування їх компонентів знижується зі зменшенням масової частки наповнювача. Отримано температурні залежності питомої теплоємності досліджуваних композитів при варіюванні часу змішування їх компонентів та масової частки наповнювача. Встановлено, що при підвищенні зазначеного часу має місце зменшення теплоємності нанокомпозитів, яка суттєво проявляється лише в області температур, близьких до температури плавлення композиційної матриці. Показано, що залежність густини нанокомпозитів від часу змішування їх компонентів у якісному відношенні є подібною до відповідної залежності для їх теплопровідності. Отримані дані можуть використовуватися для вибору часу змішування нанокомпозиційних компонентів матеріалів при розробці відповідної технології їх отримання

22 December 2021 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
NFNataliia Fialko
Nataliia Fialko
RDRoman Dinzhos
Roman Dinzhos
JSJulii Sherenkovskii
Julii Sherenkovskii
NMNataliia Meranova
Nataliia Meranova
SASergii Aloshko
Sergii Aloshko
LNLiudmyla Nedbaievska
Liudmyla Nedbaievska
This paper reports a series of experimental studies to establish regularities of the integrated effect exerted on the specific heat capacity of polymer nanocomposites by such factors as the temperature regime of their production, the value of the mass fraction of the filler, and the temperature of the composite material. The studies were conducted for nanocomposites based on polypropylene filled with carbon nanotubes. When obtaining composites, the method of mixing the components in the melt of the polymer was used. During the studies, the temperature of nanocomposites varied from 295 to 455 K, the mass fraction of the filler ‒ from 0.3 to 10 %. The basic parameter of the technological mode for obtaining composite materials, the value of overheating the polymer melt relative to its melting point, varied in the range of 10...75 K. It is shown that the temperature dependence of the specific heat capacity of the considered composites is sensitive to changes in the overheating of the polymer melt only in the region maximum values of the specific heat capacity. Concentration dependences of the specific heat capacity of the considered nanocomposites at different values of their temperature and the level of overheating of the polymer melt have been built. The studies have been carried out to identify the effects of the influence of the above parameters on the coefficient of thermal diffusivity of nanocomposites. It has been established, in particular, that an increase in the level of overheating the polymer could lead to a very significant increase in the coefficient of thermal diffusivity, which is all the more significant the higher the proportion of filler and the lower the temperature of the composite material. It is shown that the level of overheating the polymer melt relative to its melting point is a parameter that can be used as the basis for the creation of polymer composite materials with specified thermophysical properties. Выполнен цикл экспериментальных исследований по установлению закономерностей комплексного влияния на удельную теплоемкость полимерных нанокомпозитов таких факторов, как температурный режим их получения, величина массовой доли наполнителя и температура композиционного материала. Исследования проведены для нанокомпозитов на основе полипропилена, наполненного углеродными нанотрубками. При получении композитов использовался метод смешения компонентов в расплаве полимера. В ходе исследований температура нанокомпозитов изменялась от 295 до 455 K, массовая доля наполнителя – от 0,3 до 10 %. Основной параметр технологического режима получения композиционных материалов – величина перегрева расплава полимера относительно температуры его плавления –варьировалась в диапазоне 10…75 K. Показано, что температурная зависимость удельной теплоемкости рассматриваемых композитов является чувствительной к изменению перегрева расплава полимера только в области ее максимальных значений. Получены концентрационные зависимости удельной теплоемкости рассматриваемых нанокомпозитов при различных значениях их температуры и уровня перегрева расплава полимера. Выполнены исследования по выявлению эффектов влияния указанных выше параметров на коэффициент температуропроводности нанокомпозитов. Установлено, в частности, что увеличение уровня перегрева полимера может приводить к весьма значительному повышению коэффициента температуропроводности, которое оказывается тем более существенным, чем выше доля наполнителя и ниже температура композиционного материала. Показано, что уровень перегрева расплава полимера относительно температуры его плавления является параметром, который может быть положен в основу создания полимерных композиционных материалов с заданными теплофизическими свойствами Виконано цикл експериментальних досліджень щодо встановлення закономірностей комплексного впливу на питому теплоємність полімерних нанокомпозитів таких факторів, як температурний режим їх отримання, величина масової частки наповнювача і температура композиційного матеріалу. Дослідження проведено для нанокомпозитів на основі поліпропілену, наповненого вуглецевими...

16 November 2018 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
NFNataliia Fialko
Nataliia Fialko
ASAlla Stepanova
Alla Stepanova
RNRaisa Navrodska
Raisa Navrodska
NMNataliia Meranova
Nataliia Meranova
YSYulii Sherenkovskii
Yulii Sherenkovskii
Efficiency of the air heater in a heat recovery system at different thermophysical parameters and operational modes of the boiler

3 October 2025 in Energy Technologies & Resource Saving
Verified
Journal Article
Open access
PDF file
NFN.M. Fialko
N.M. Fialko
ОSО.I. Sigal
О.I. Sigal
AKA.A. Khalatov
A.A. Khalatov
DPD.YU. Paderno
D.YU. Paderno
NMN.O. Meranova
N.O. Meranova
YSYu.V. Sherenkovskiy
Yu.V. Sherenkovskiy
The article presents the results of the analysis of a number of issues in the context of the problem of covering peak loads in the energy system of Ukraine. Information is provided on the features of the formation of these loads and their changes due to the full-scale invasion of Russia into Ukraine. The corresponding challenges associated with the integration of renewable energy sources into the energy system of Ukraine are considered. The specifics of the implementation of both traditional and innovative approaches to covering peak loads are analyzed, in particular the use of peak generating capacities, energy storage systems, smart grids and demand management, as well as the integration of renewable sources into the energy system in combination with energy storage devices or virtual power plants. The data on the comparison of the characteristics of different types of peak capacities in terms of peak load coverage efficiency are provided. Particular attention is paid to the consideration of the prospects for the development of peak load coverage technologies in Ukraine. It is indicated that in the short term, traditional approaches will have a certain advantage over innovative ones. As for innovative approaches, one of the most promising will be the use of battery systems. Approaches related to demand management and the use of renewable energy sources in combination with energy storage and virtual power plants will remain important. Based on the results of the analysis, a conclusion was made about the growing relevance of the problem of covering peak loads in the energy system of Ukraine, given the increase in these loads due to a number of reasons, including unavoidable ones. Bibl. 44, Fig. 3, Tab. 3.

27 July 2018 in Scientific Bulletin of UNFU
Verified
Journal Article
Open access
NFN. M. Fialko
N. M. Fialko
RDR. V. Dinzhos
R. V. Dinzhos
YSYu. V. Sherenkovskyi
Yu. V. Sherenkovskyi
VPV. G. Prokopov
V. G. Prokopov
NMN. O. Meranova
N. O. Meranova
GIG. V. Ivanenko
G. V. Ivanenko
Встановлено закономірності структуроутворення під час кристалізації полімерних нанокомпозитів на основі поліетилену, наповненого вуглецевими нанотрубками. Виявлено ефекти впливу на ці закономірності таких факторів, як масова частка наповнювача, швидкість охолодження і метод отримання композитів. Розгляду підлягали нанокомпозити, отримані методом, що базується на змішуванні компонентів у сухому вигляді і в розплаві полімеру. Виконано зіставлення експериментальних екзотерм кристалізації для досліджуваних композитів за зазначених методів їх отримання. З використанням екзотерм кристалізації і рівняння нуклеації отримано дані про особливості структуроутворення на початковій стадії кристалізації композитів. Встановлено, що на цій стадії наявний площинний і об'ємний механізм структуроутворення за деякого переважання останнього. Виконано аналіз закономірностей структуроутворення на стадії кристалізації в об'ємі композитів у цілому в припущенні наявності двох механізмів кристалоутворення, перший з яких пов'язаний з кристалізацією на флуктуаціях густини полімеру, другий – із кристалізацією, в якій роль її центрів відіграють частинки наповнювача. Показано, що механізми кристалізації на частинках наповнювача істотно залежать від його масової частки і методу отримання композиційних матеріалів.