1 January 2023 in Machine Science Journal
22 January 2024 in International Journal of Modern Physics B
25 June 2024 in Polymer-Plastics Technology and Materials
29 March 2024 in Materials Science Forum
Cd1-0.06Mn0.06Te epitaxial thin films were synthesis on glass substrates by the Molecular Beam Condensation (MBC) method in the vacuum evaporation equipment УВН-71-ПЗ with steam-oil pumping and nitrogen trap at working pressure of residual gas (1÷2)x10-4 Pa. By using additional source of Te vapor and controlling temperature, it has been determined the optimum conditions for obtaining Cd1-0.06Mn0.06Te epitaxial films with a perfect structure, clean and smooth surface, without of second phase inclusions. XRD investigations showed that Cd1-0.06Mn0.06Te epitaxial films grow on glass substrates on the (111) plane of the face-centered cubic lattice with the lattice parameter of a = 6.481 Å. Effect of γ-irradiation on XRD spectra of Cd1-0.06Mn0.06Te epitaxial films reveals that, XRD patterns of initial and γ-irradiated samples did not show any phase transformations, however there is a variation in relative intensities of diffraction peaks. It has been found that Cd1-0.06Mn0.06Te epitaxial films with a film thickness of d=15 µm, absorb light up to a wavelength of λ=765 nm and at λ>765 nm the absorption begins to gradually decrease and then the material becomes transparent. The obtained results indicate that Cd1-0.06Mn0.06Te epitaxial films absorb light quanta in the visible and infrared spectral regions. Iirradiation of Cd1-0.06Mn0.06Te epitaxial films with γ rays at low irradiation doses leads to a change in the optical parameters, the profile of the spectrum curves and the intrinsic absorption edge. In additions to experimental studies, a theoretical ab initio calculations of band structure (BS) of ideal and defective semiconductors of Cd1-0.06Mn0.06Te has been also carried out by using Density Functional Theory (DFT) method via Atomistix ToolKit computer program. The band gap energy has been calculated as Eg = 1.6 eV for ferromagnetic (FM) and Eg = 1.7 eV for antiferromagnetic (AFM) state of Cd1-0.06Mn0.06Te compound. The results of theoretical calculations on the band gap energy of ideal and defective Cd1-0.06Mn0.06Te semiconductors are in a good agreement with experimental findings.
29 November 2024 in Research Square
Polyurethane based composite formulation is developed, characterized by a significantly low amount of additives and their technological compatibility. It is shown that content of 0,05 mass% boron nitride in the polyurethane composition is optimal, as it leads to an increase in the mechanical strength of the film. This study presents temperature-time dependence of the mechanical strength of polyurethane films and the influence of BN additives on these characteristics. İt was defined that the observed increase in film strength at incorporating 0,05% by mass of BN to its content, associated with changes in the supramolecular structure, specifically the formation of spherulitic microstructure of supramolecular polyurethane. In the mechanical field, the bond rupture process is accelerated, thus the role of the load involves reducing bond energy, altering the distance between kinetic units, and fixing their movements, particularly difficulty of recombination of radicals. The structure of the formula in the durability equation suggests that the contribution of the load to bond rupture is represented by the term ασ mechanical field work. Throughout the entire range of applied loads, the product of ασ was significantly lower than activation energy. Therefore, the thermal fluctuations are the main factor causing breakdown, meaning the energy for body rupture is largely derived from thermal energy reserves rather than external work. Initial activation energy for mechanical failure of PU films and its optimally modified state remains unchanged. However, the additive influences to the magnitude of the structural sensitivity coefficient and the mechanical strength, so rupture occurs through chemical bonds.