Ensuring the microbiological safety of food products is a problem of current interest. The use of antimicrobial packaging materials is a way of solving the problem. When developing packaging materials, it is advisable to use a modern approach based on the creation of biodegradable materials. The difficulty in the selection of the polymer compositions’ components lies in solving the dilemma of the joint introduction and processing of antimicrobial and biodegradable agents. The studies of the ultrasound treatment on the melts of polymer mixtures showed an increase in the dispersion process of the components of the mixture. In this regard, this work aimed to study the effect of the ultrasonic treatment on the melts of polymer compositions containing thermoplastic starch and birch bark extract (BBE). In the work, the properties of PE-based packaging materials with various BBE concentrations obtained with ultrasonic treatment of melts on a laboratory extruder were studied. Biodegradable polymer compositions containing thermoplastic starch and BBE, obtained with the use of the ultrasonic treatment during extrusion, were investigated. The methods for studying rheological, physic-mechanical, antimicrobial properties and sanitary chemical indicators of materials were used in the article. It was found that ultrasonic treatment increases the melt flow and contributes to the production of materials with the uniform distribution of additives. The BBE content from 1.0% and higher in the contents of the material provides antimicrobial properties. When studying the permeability of oxygen and water vapor of the polymer compositions based on PE and BBE, it was found that the introduction of a filler increases vapor permeability by about 8–12% compared with control samples. The optimal concentration of BBE in polyethylene compositions containing thermoplastic starch was determined. The extension of the shelf life of the food product during storage in the developed material was established.
Particular attention is paid to biodegradable materials from the environmental point of view and antimicrobial materials that ensure the microbiological safety of packaged products. The aim of the work was to study the properties of the composition, based on biodegradable polybutylene adipate terephthalate (PBAT) and the antimicrobial additive—birch bark extract (BBE). Test samples of materials were obtained on the laboratory extruder by extrusion with ultrasonic treatment of the melt. The concentration of the antimicrobial additive in the polymer matrix was 1 wt %. A complex research was carried out to study the structural, physico–mechanical characteristics, antimicrobial properties and biodegradability of the modified PBAT. Comparative assessment of the physico–mechanical characteristics of samples based on PBAT showed that the strength and elongation at break indices slightly decrease when the ultrasonic treatment of the melt is introduced. It was found out, that the antimicrobial additive in the composition of the polymer matrix at the concentration of 1 wt % has a static effect on the development of microorganisms on the surface of the studied modified films. Studies of the biodegradability of modified PBAT by composting for 4 months have shown that the decomposition period of modified materials increased, compared to pure PBAT. The developed modified polymer material can be recommended as an alternative replacement for materials based on polyethylene for food packaging.
Films based on PVA solutions are currently attracting increasing attention due to their high transparency, barrier properties and environmentally friendly nature. This is due to the fact that PVA films have greater flexibility, transparency, impact strength and lower cost than other packaging materials. When discarded, PVA can decompose in the natural environment without adding to the pollution. The article is devoted to the study of film materials obtained from modified solution systems based on polyvinyl alcohol (PVA). Polyvinyl alcohol grade 098–10 was used as the starting product; glycerin grade T 94 was used as a plasticizer. The films were cast on glass, then heated in a heating cabinet at a temperature of 90 °C for 31 hours. The influence of different concentrations of PVA solutions on the barrier (vapor permeability) and physical and mechanical properties of films was studied. It was shown that, with an increase in the concentration of glycerol in PVA, the fracture resistance increased, the relative elongation noticeably decreased, and the permeability of the polymer sharply increased. The introduction of 20–30% plasticizer into PVA resulted in the production of a sufficiently elastic film, an increase in elongation at break, and also a decrease in tensile strength. The complex of studies carried out made it possible to determine the influence of modifying additives on the structural transformations of PVA compositions for the creation of new generation coatings. In the future, it is planned to continue research on this topic, in particular on optimizing the temperature-time regime of coating formation
В статье рассматривается актуальный вопрос создания модифицированных полимерных композиций на основе порошкового фторопласта для антиадгезионных термостойких покрытий. В настоящее время сложность создания разделительных покрытий пищевого назначения обусловлена ограниченным выбором полимерных материалов, пригодных для покрытий, контактирующих с продуктами питания, обладающих высокой термостойкостью, а также низкой поверхностной энергией, ответственной за уровень адгезионного взаимодействия с пищевыми средами. Для исследования комплекса структурных характеристик использованы методы сканирующей электронной микроскопии, ИК-спектроскопии. Исследованы как поперечные срезы, так и поверхность покрытий, что позволило установить, что причиной улучшенных механических характеристик модифицированных покрытия является равномерное распределение их по объему, приводящее к гомогенизации структуры, формированию гладкой поверхности покрытий и бездефектной границы раздела «металл-покрытие».
Исследование влияния ультразвуковой обработки полиэтиленовых композиций, содержащих бетулин, на формирование эксплуатационных свойств упаковочных материалов