The strong parameter dependency of model predictive control (MPC), despite its capability to enhance dynamic performance in dual-active-bridge (DAB) converters, remains a critical limitation. To overcome the parameters’ uncertainty of DAB, this paper proposes a model-free predictive control (MFPC) method integrated with a sliding mode observer (SMO). First, to enhance the steady-state efficiency of the DAB converter, optimization strategies for natural zero-voltage switching (ZVS) and full ZVS are proposed under the constraint of minimum current stress. A comprehensive analysis of the advantages and disadvantages of both methods is conducted, and the most efficiency-optimal approach is selected based on experimental results. Second, an ultra-local model of the DAB converter is established, which innovatively consolidates all uncertainties into a unified lumped disturbance. A full-order SMO is employed to estimate the lumped disturbance in real time, replacing traditional parameter identification techniques. This reduces computational burden while enhancing system robustness. Finally, experimental comparisons with other schemes validate the effectiveness and superiority of the proposed method.
12 September 2025 in IEEE Transactions on Power Electronics
Decentralized integration of distributed generation (DG) units and loads are increasing in the modern distribution grid. Maintaining the power flow and power quality within their accepted limits is a challenging task. This article proposes a medium-voltage dc (MVDC) interconnection system based on the single-stage multiport solid-state transformers (SST). First, the single-stage multiport SST’s coordinated control strategies and energy management method are discussed, aiming at the flexible power flow control between the utility grid, MVDC grid, and the low-voltage ac/dc microgrid. Second, the MVDC controller parameters and SST passive components are optimized based on the impedance interaction characteristics between the two SSTs’ MVDC ports, thereby enhancing the stability margin of the interconnected system. Then, the operation modes of the interconnected system are defined. Finally, the effectiveness of the proposed operation modes and control strategy is verified through a 1-MW simulation platform, while a 1-kW scaled-down experimental prototype is built to further validate the single-stage multiport SST and the MVDC interconnected system.
1 January 2026 in IEEE Journal of Emerging and Selected Topics in Power Electronics
The paper presents a broadband design method using simplified real frequency technology (SRFT) and Class-F mode for high-efficiency power amplifiers (PAs). The traditional combination of SRFT with Class-F mode is generally based on Load-Pull technology with the harmonic control network of Class-F PA which will restrict the broaden of frequency band to a certain extent. It will make the results unsatisfactory in the direct optimization process later. The proposed method in this paper is to fit the corresponding Class-F harmonic control network in the process of designing matching network using SRFT. And then the network will be optimized in the synthesis of network. There will be no case that the harmonic control network restricts the bandwidth. In this paper, a broadband PA is designed with CGH40010F transistor based on SRFT and Class-F PA theory. When the input power is 30 dBm, power added efficiency (PAE) can reach more than 60% over a 54.5% bandwidth from 1.6 GHz to 2.8 GHz. In the frequency range of 1.7–2.4 GHz, the PAE can reach more than 70%, the gain ranges from 10 dB to 12.7 dB and the output power over 40dBm.
20 March 2026 in IEEE Transactions on Power Electronics
The enhanced soft normally-open point (e-SNOP) regulates the power flow of medium-voltage ac (MVAC) feeders, while providing low-voltage dc (LVDC) ports for the flexible integration of distributed energy resources. However, its implementation typically requires a large number of power converters. To address this issue, this paper proposes a series- shunt e-SNOP topology integrated with photovoltaic (PV) and energy storage. The shunt unit of this topology offers multiple LVDC ports, enabling the direct connection of distributed PV generation and energy storage, while the series unit features expendable MVAC feeder interfaces to support flexible power flow regulation. Meanwhile, this topology adopts a single-stage dc-ac submodule design, reducing capacitors and simplifying control strategy complexity. First, this paper introduces the topological configuration and its submodule's working principles. Then, its average circuit model is established. Additionally, the three operation modes and their corresponding control strategies are designed. Finally, the effectiveness of the proposed control strategies is verified through a 10-kV/3-MW full power simulation platform, and a 1-kW scaled-down experimental prototype is built to further demonstrate the correctness of the proposed topology.