Surface transfer doping of diamond has been demonstrated using MoO3 as a surface electron acceptor material. Synchrotron-based high resolution photoemission spectroscopy reveals that electrons are transferred from the diamond surface to MoO3, leading to the formation of a sub-surface quasi 2-dimensional hole gas within the diamond. Ex-situ electrical characterization demonstrated an increase in hole carrier concentration from 1.00 × 1013/cm2 for the air-exposed hydrogen-terminated diamond surface to 2.16 × 1013/cm2 following MoO3 deposition. This demonstrates the potential to improve the stability and performance of hydrogen-terminated diamond electronic devices through the incorporation of high electron affinity transition metal oxides.
Surface transfer doping of hydrogen-terminated diamond has been achieved utilising V2O5 as a surface electron accepting material. Contact between the oxide and diamond surface promotes the transfer of electrons from the diamond into the V2O5 as revealed by the synchrotron-based high resolution photoemission spectroscopy. Electrical characterization by Hall measurement performed before and after V2O5 deposition shows an increase in hole carrier concentration in the diamond from 3.0 × 1012 to 1.8 × 1013 cm−2 at room temperature. High temperature Hall measurements performed up to 300 °C in atmosphere reveal greatly enhanced thermal stability of the hole channel produced using V2O5 in comparison with an air-induced surface conduction channel. Transfer doping of hydrogen-terminated diamond using high electron affinity oxides such as V2O5 is a promising approach for achieving thermally stable, high performance diamond based devices in comparison with air-induced surface transfer doping.
Homoepitaxial diamond has been used to demonstrate the RF performance of 50-nm gate length hydrogen-terminated diamond field-effect transistors. An extrinsic cutoff frequency of 53 GHz is achieved which we believe to be the highest value reported for a diamond-based transistor. The generation of an RF small signal equivalent circuit is used to extract device elements to better understand variation between intrinsic and extrinsic operation. An intrinsic cutoff frequency of 90 GHz is extracted through this process, verifying the requirement to minimize access resistance to maximize the potential high-frequency performance of this technology.
We report on optimisation of the environmental stability and high temperature operation of surface transfer doping in hydrogen-terminated diamond using MoO3 and V2O5 surface acceptor layers. In-situ annealing of the hydrogenated diamond surface at 400 °C was found to be crucial to enhance long-term doping stability. High temperature sheet resistance measurements up to 300 °C were performed to examine doping thermal stability. Exposure of MoO3 and V2O5 transfer-doped hydrogen-terminated diamond samples up to a temperature of 300 °C in ambient air showed significant and irreversible loss in surface conductivity. Thermal stability was found to improve dramatically however when similar thermal treatment was performed in vacuum or in ambient air when the oxide layers were encapsulated with a protective layer of hydrogen silsesquioxane (HSQ). Inspection of the films by X-ray diffraction revealed greater crystallisation of the MoO3 layers following thermal treatment in ambient air compared to the V2O5 films which appeared to remain amorphous. These results suggest that proper encapsulation and passivation of these oxide materials as surface acceptor layers on hydrogen-terminated diamond is essential to maximise their environmental and thermal stability.
Developments over the last 15 years in the areas of materials and devices have finally delivered competitive III-V MOSFETs with high mobility channels. This paper briefly reviews the above developments, discusses properties of the GdGaO/ Ga2O3 MOS systems, presents GaAs MOSFET DC and RF data, and concludes with an outlook for high indium content channel MOSFETs. GaAs based MOSFETs are potentially suitable for RF power amplification, switching, and front-end integration in mobile and wireless applications while MOSFETs with high indium content channels are of interest for future CMOS applications.
12 December 2016 in Journal of Materials Chemistry A
Metal chalcogenides, and doped molybdenum sulfides in particular, have considerable potential as earth-abundant electrocatalysts for the hydrogen evolution reaction. This is especially true in the case of solar-to-hydrogen devices, where an ability to deposit these materials on transparent substrates is therefore desirable. Hydrothermal methods are perhaps the most common route by which metal chalcogenide materials suitable for the hydrogen evolution reaction are produced. Such methods are simple and scalable, but the direct hydrothermal deposition of metal chalcogenides on transparent oxide electrodes has hitherto never been reported. Such an advance would greatly facilitate the expansion of the field by removing the requirement for separate hydrothermal-synthesis and catalyst-deposition steps. In this paper, we show that the ternary chalcogenide Co2Mo9S26 can be synthesised on a fluorine-doped tin oxide substrate by hydrothermal methods directly from solutions of the simple metal salts. These films display good activity for the hydrogen evolution reaction from acid solution, achieving current densities of 10 mA cm−2 at 260 mV overpotential with a Tafel slope of 64 mV per decade. Moreover, the resulting films can be made to be translucent, a very useful property which would allow light to be transmitted through the catalyst to an underlying light-harvesting array in any solar-to-hydrogen device employing this material at the cathode.