22 October 2020 in IEEE Transactions on Vehicular Technology
In order to keep the lithium-ion battery within the optimal temperature range to achieve excellent battery performance and extend its lifespan, it is necessary to have an effective control strategy for a low-temperature battery thermal management system (BTMS) consisting of electric pump, cooling plate and radiator. In this paper, a control-oriented model for BTMS is established, and an intelligent model predictive control (IMPC) strategy is developed by integrating a neural network-based vehicle speed predictor (VSP) and a target battery temperature adaptor based on Pareto boundaries. The strategy developed based on the BTMS model is applied to plug-in electric vehicles operating in electric vehicle (EV) mode, and the results show its superiority in terms of battery temperature control, battery lifespan extension and energy saving. Under the new European driving cycle, the average difference between the real-time battery temperature under the novel IMPC and its target temperature is 0.26 °C, and the maximum temperature difference among modules is 1.03 °C. Moreover, compared with the on-off controller, model predictive control (MPC), and MPC with VSP, the state of health under IMPC at the end of the driving cycle is 0.016%, 0.012%, and 0.008% higher, respectively. At the end of the driving cycle, the energy consumption of IMPC is 24.5% and 14.1% lower than that of the on-off controller and traditional MPC, respectively.
24 August 2022 in IEEE Transactions on Industrial Electronics
Energy storage system based on batteries is a key to achieve a green industrial economy and the online estimation of its status is critical for the battery management system. Therefore, this article proposed a distributed spatial–temporal online correction algorithm for the state of charge (SOC) three-dimensional (3-D) state of temperature (SOT) coestimation of battery. First, the internal resistance is identified, and SOC is estimated based on the adaptive Kalman filter. Then, to improve the fidelity of electrical status estimation under the dynamic operation condition, the SOC estimation is coupled with an online restoration algorithm of distributed temperature. An improved fractal growth process is used to achieve the self-organization and convergence during the restoration of 3-D temperature distribution. Finally, to validate the fidelity of online coestimation algorithm for electrical and thermal parameters, dynamic current profiles are used. The coestimation method raises the fidelity of SOC estimation by 1.5% at most, compared with the SOC estimation algorithm without the SOT estimation. It also keeps the mean relative error of SOT estimation within 8%. Additionally, the robustness of the spatial–temporal online correction method with dual adaptive Kalman filters is validated. The result shows that the coestimation algorithm still has a good convergence performance with disturbance added.
5 July 2019 in IEEE Transactions on Power Electronics
This paper devises an innovative mesoscale electrothermal model for Li-ion batteries. This model manipulates the mesoscale calculation grid in finite element analysis as independent small cell sandwiches and establishes a lumped equivalent circuit model for each cell sandwich. Then, such electrical models are arranged in parallel to form a multilayer equivalent circuit to simulate electrical characteristics of a whole battery, through capturing the current and terminal voltage of each constituent cell sandwich. This modeling idea overcomes the entrenched disadvantage of heat generation models with lumped parameters, i.e., the unavailability of heat generation distribution inside a battery. Besides the current and terminal voltage, the temperature and state of charge dependent open-circuit voltage and entropy coefficient are incorporated into a Newman's heat generation model to estimate the heat generated in the calculation grid. The battery temperature distribution is eventually derived by solving the heat conduction equation with thermal conductivity as a function of the battery temperature. We leverage the developed electrothermal model to track the temperature evolution of an 18 650 Li-ion battery at different ambient temperatures and discharge rates, for the first time. Experimental results demonstrate that the electrothermal model can precisely emulate the battery thermal dynamics with an average error of 0.72 °C. Moreover, a comparative study shows that the proposed model outperforms common resistance-based thermal models that do not consider the heat generation distribution and the interdependence between the battery temperature and thermal conductivity.
1 May 2023 in IEEE Transactions on Vehicular Technology
AC pulse heating is a promising preheating method for lithium-ion batteries due to its low energy cost and high efficiency. To avoid the lithium plating in the AC heating, upper bound of heating current (UBHC) should be obtained. In this paper, the dual RC model is developed, and coupled with the thermal model to predict the battery temperature and potential of negative electrode (PNE). PNE=0 V is used as the lithium plating criteria. If the PNE falls to 0 V during the heating process, the lithium plating is triggered, and the corresponding pulse amplitude is the UBHC. Moreover, because the UBHC increases with the battery temperature, the pulse amplitude should be automatically raised to increase the heating efficiency. When the battery temperature is too low, the UBHC is so small that the AC pulse heating is inapplicable. Through the self-adaptive AC pulse based on the UBHC, the heat strategy is built, and the heating time is calculated. The total heating time reached by the proposed strategy increases with the increment of the initial SOC, and it falls with the decrease of the initial battery temperature. Moreover, the heating time has a temperature limit. If the battery temperature is lower than the limit, the battery cannot be heated to the target temperature in the required time. The proposed strategy is applied to heating the battery at the different SOCs, and its performance is compared to the constant amplitude pulse. In the same heating time, the battery temperature achieved by the proposed strategy is at least 7.6 °C higher than the constant amplitude pulse. Moreover, the UBHC is enlarged by 10% to prove the original UBHC can reduce the degradation. The cyclic heating experiment shows that the 110% UBHC reaches a capacity loss of 0.49 Ah after 60 heating cycles and that of the original UBHC is only 0.1 Ah.
6 August 2021 in IEEE Transactions on Power Electronics
Large battery packs are used in electric vehicles. Heat is generated when the battery pack is being used. Therefore, it is necessary to predict battery heat generation. An enhanced electro-thermal model is developed to describe the temperature distribution inside a battery pack. It combines the dynamic resistance model and the current distribution model. The resistance model is affected by the thermal and electrical parameters, while the current distribution model considers the interaction between cell status and current variation in the parallel branch. The proposed model can accurately predict the temperature change of cells in the pack under static and dynamic current conditions. Experiments are conducted to validate the prediction accuracy. Most of the average absolute errors (AE ave ) between the predicted value and test value displayed on the experimental device do not exceed 0.4 °C under static current conditions, and all of them are below 0.1 °C under dynamic current conditions. The two existing models, namely the state-of-charge (SOC)-dependent resistance model [R(SOC)] and SOC-T-dependent resistance model [R(SOC, T)], have AE ave values of 1.6 and 0.54 °C when the pack is discharged at 0.5 C. In contrast, the AE ave value achieved by our proposed model is 0.4 °C. Under dynamic current conditions, the maximum AE ave s are 0.42 °C for the R(SOC) model, 0.26 °C for the R(SOC, T) model, and 0.16 °C for the proposed model. These results demonstrate that the proposed model provides more accurate predictions of the temperature rise inside the pack than the popular existing models.
29 February 2024 in Energy