Wei-En Fu

Wei-En Fu

Auto-generated profile, based on publicly available information

Wei-En Fu

Institute of Industrial Technology Research, Center for Measurement Standards, Advanced Process Instrumentation and Materials Metrology Laboratory, Hsinchu, Taiwan

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2023 in Surface Topography: Metrology and Properties
Verified
Journal Article
Closed access
PDF file
WFW E Fu
W E Fu
BHB C He
B C He
WWWen-Li Wu
Wen-Li Wu
Transmission small angle x-ray scattering (tSAXS) has been developed as a metrology for the critical dimension (CD) measurements to facilitate integrated circuit (IC) chip fabrications. Synchrotron x-ray sources were used for their high brilliance and a wavelength less than one tenth of a nanometer was chosen for its high penetration power to enable transmission measurements through a silicon wafer with a nominal thickness of 0.7 mm. A major hold back preventing tSAXS from reaching wide applications in IC fabrication is the lack of high brilliance laboratory-based x-ray sources. Within the last few years, even without any major breakthrough in x-ray source technology, this tSAXS metrology has finally been used for 3D NAND and DRAM, i.e., memory chips with tall or high aspect ratio (HAR) architectures. The scattering intensities from HAR structures will be discussed quantitatively in terms of the sample height and the effective longitudinal coherence length of the incident x-ray.

1 January 2009
Verified
Conference Paper
Closed access
WFWei-En Fu
Wei-En Fu
YCYong-Qing Chang
Yong-Qing Chang
YCYi-Ching Chen
Yi-Ching Chen
ESErik M. Secula
Erik M. Secula
DSDavid G. Seiler
David G. Seiler
ADAlain C. Diebold
Alain C. Diebold
High‐k materials, such as HfO 2 , Al 2 O 3 , and many others, have been employed to replace the SiO 2 insulator in the gate dielectric device in order to offer significant gate leakage reduction. In this study, the physical properties of hafnium dioxide ( HfO 2 ) thin films were analyzed and characterized in the cases of ‘as‐deposited’ and ‘post‐deposition annealing’ (PDA). Ultra‐thin hafnium dioxide films of thickness 2.5, 5 and 10 nm were deposited on Si (100) substrates using atomic layer deposition (ALD) at temperature of 300° C. After deposition, the films were annealed using furnace in Ar ambient for 10 minutes at 450° C, 550° C, 650° C and 750° C. The thickness, density, roughness and the crystalline evolution of the HfO 2 films were investigated by Grazing Incidence X‐Ray Reflectometry (GIXRR) and Grazing Incidence X‐Ray Diffraction (GIXRD) for both as‐deposited and post‐annealing conditions. Transmission Electron Microscope (TEM) was used to provide image verification of the two‐layer model applied in XRR fitting analysis. Furthermore, the grain sizes were evaluated by X‐ray diffraction peak‐broadening (full width at half maximum, FWHM) calculation according to the Scherrer method. The experimental results showed that the annealing temperatures had significant impact on the thickness, density and roughness of the HfO 2 and SiO 2 layers. In addition, the experimental results demonstrated the grain sizes depend on not only the thickness of the film, but also the annealing temperatures in the crystallization process.

1 January 2026 in Journal of Micro/Nanopatterning, Materials, and Metrology
Verified
Journal Article
Closed access
GPGaurav Pandey
Gaurav Pandey
WFWei-En Fu
Wei-En Fu
CLChun-Yu Liu
Chun-Yu Liu
Chao-Ching HoChao-Ching Ho
Chao-Ching Ho
LCLiang-Chia Chen
Liang-Chia Chen
Background: Advanced semiconductor logic nodes have shifted toward gate-all-around (GAA) architectures, such as Nanosheet, Forksheet, and complementary field-effect transistor devices. This shift has imposed more stringent measurement requirements at the front-end-of-line process stages. As the GAA architecture has been advanced to improve device performance, power efficiency and reduce device dimensions, the complexity in structural design and material integration is observed. A fundamental limit in structural characterization for GAA devices has been reached by conventional metrology, primarily due to the intricate 3D, high-aspect-ratio vertical stacked channels with buried nanoscale features.Aim: To address these complexities and support process control, several metrologies are reviewed, with an emphasis on X-ray metrology and the inclusion of other relevant metrologies.Review Approach: Recent developments in metrology are discussed in detail. Analysis is focused on measurement configurations, in-line applicability, and advancements aligned with the demands of next-generation logic nodes.Conclusion: The correspondence between X-ray metrology advancements and architecture-driven requirements is evaluated in this review. X-ray metrology developments are assessed for the potential to facilitate the characterization of 3D nanoscale features within future logic device fabrication.