1 January 2001 in Journal of the Electrochemical Society
The dry etching characteristics of ZnO using an inductively couple plasma (ICP) have been investigated, for the first time, as functions of plasma chemistry, radio frequency (rf) table power, and ICP power. The <mml:math display="inline"><mml:msub><mml:mo>CH</mml:mo><mml:mrow><mml:mn>4</mml:mn></mml:mrow></mml:msub><mml:mo>/</mml:mo><mml:msub><mml:mo>H</mml:mo><mml:mrow><mml:mn>2</mml:mn></mml:mrow></mml:msub></mml:math>CH4/H2 etchant gases resulted in the highest etch rate of ZnO, suggesting that the etching of Zn in ZnO largely involves a process in which a volatile metallorganic zinc compound, such as <mml:math display="inline"><mml:mi mathvariant="normal">Zn</mml:mi><mml:mo stretchy="false">(</mml:mo><mml:msub><mml:mo>CH</mml:mo><mml:mrow><mml:mn>3</mml:mn></mml:mrow></mml:msub><mml:msub><mml:mo stretchy="false">)</mml:mo><mml:mrow><mml:mi mathvariant="normal">y</mml:mi></mml:mrow></mml:msub></mml:math>Zn(CH3)y is formed. The etch rate was increased with increasing rf table power, and the highest etch rate of 2000 Å/min was achieved at an rf table power of 200 W (dc bias: −80 V). As the ICP power was increased, the etch rate also increased, which suggests that the plasma density is also an important factor in this process. Furthermore, it was observed that hydrogen-containing plasma etching enhances the band-edge photoluminescence of the ZnO film. © 2000 The Electrochemical Society. All rights reserved.
19 December 2017 in Scientific Reports
BHBastian Waduge Naveen Harindu Hemasiri
Bastian Waduge Naveen Harindu Hemasiri
Indium tin oxide (ITO) still remains as the main candidate for high-performance optoelectronic devices, but there is a vital requirement in the development of sol-gel based synthesizing techniques with regards to green environment and higher conductivity. Graphene/ITO transparent bi-film was synthesized by a two-step process: 10 wt. % tin-doped ITO thin films were produced by an environmentally friendly aqueous sol-gel spin coating technique with economical salts of In(NO3)3.H2O and SnCl4, without using organic additives, on surface free energy enhanced (from 53.826 to 97.698 mJm−2) glass substrate by oxygen plasma treatment, which facilitated void-free continuous ITO film due to high surface wetting. The chemical vapor deposited monolayer graphene was transferred onto the synthesized ITO to enhance its electrical properties and it was capable of reducing sheet resistance over 12% while preserving the bi-film surface smoother. The ITO films contain the In2O3 phase only and exhibit the polycrystalline nature of cubic structure with 14.35 ± 0.5 nm crystallite size. The graphene/ITO bi-film exhibits reproducible optical transparency with 88.66% transmittance at 550 nm wavelength, and electrical conductivity with sheet resistance of 117 Ω/sq which is much lower than that of individual sol-gel derived ITO film.
28 November 2017 in Nano-Micro Letters
BHBastian Waduge Naveen Harindu Hemasiri
Bastian Waduge Naveen Harindu Hemasiri
The combination of graphene with conductive nanoparticles, forming graphene–nanoparticle hybrid materials, offers a number of excellent properties for advanced engineering applications. A novel and simple method was developed to deposit 10 wt% tin-doped indium tin oxide (ITO) nanoparticles on graphene. The method involved a combination of a solution-based environmentally friendly electroless deposition approach and subsequent vacuum annealing. A stable organic-free solution of ITO was prepared from economical salts of In(NO3) 3 · H2O and SnCl4. The obtained ITO nanostructure exhibited a unique architecture, with uniformly dispersed 25–35 nm size ITO nanoparticles, containing only the crystallized In2O3 phase. The synthesized ITO nanoparticles–graphene hybrid exhibited very good and reproducible optical transparency in the visible range (more than 85%) and a 28.2% improvement in electrical conductivity relative to graphene synthesized by chemical vapor deposition. It was observed that the ITO nanoparticles affect the position of the Raman signal of graphene, in which the D, G, and 2D peaks were redshifted by 5.65, 5.69, and 9.74 cm−1, respectively, and the annealing conditions had no significant effect on the Raman signatures of graphene.
28 April 2000 in Journal of Applied Physics
The fabrication and characterization of an InGaN/GaN multiple quantum well light-emitting diode (LED) with a highly transparent Pt thin film as a current spreading layer are described. The room temperature electroluminescence exhibits a strong emission at 453 nm. Pt-contacted LEDs show good electrical properties and high light-output efficiency compared to Ni/Au-contacted ones. The light transmittance and the specific contact resistance of a Pt thin film with a thickness of 8 nm on p-GaN was determined to be 85% at 450 nm and Ω cm2, demonstrating that a Pt thin film can be used as an effective current spreading layer with high light transparency.
12 February 2004 in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
We report that NH3 ambient thermal annealing is a promising method for recovering the dry- etch-induced damage on Mg-doped GaN surfaces. The surface electrical properties of dry-etched Mg-doped GaN can be fully recovered by thermal annealing using NH3 as an ambient gas at temperatures above 900 °C. The complete recovery of sheet hole concentration in dry-etched Mg-doped GaN can be attributed to a reduction in excess nitrogen vacancies in the damaged surface region by reactive nitrogen atoms supplied during NH3 ambient thermal annealing.
1 January 2019 in Journal of Alloys and Compounds