Truck suspension system could reduce cab vibration as well as road damage. A number of methods are engaged to promote truck performance, such active and semi active control. With the purpose of reducing dynamic tire force, this paper presents a simulation analysis of a semi active suspension control for light-heavy duty truck, the controller scheme known as Ground Semi Active Damping Force Estimator (gSADE). A famous tire force control oriented algorithm for heavy vehicle suspension control known as Groundhook (GRD) also has been studied. Thus, the objective of this paper is to investigate the effectiveness of the gSADE algorithm compared to GRD and passive system. These algorithms are applied to a full light-heavy duty truck models, and the simulation model was developed and simulated using MATLAB Simulink software. Ride test was conducted using random road excitation at three different speeds, and the simulation results of gSADE, GRD and passive system are compared and analyzed. The simulation results showed that the gSADE control is able to reduced tire force significantly compared to GRD control and passive system.
7 December 2021 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
In this article, a numerical approach is applied to study the flow regimes surround a generic train model travelling on different bridge configurations under the influence of crosswind. The bridge is varies based on the different geometry of the bridge girder. The crosswind flow angle (Ψ) is varied from 0° to 90°. The incompressible flow around the train was resolved by utilizing the Reynolds-averaged Navier-Stokes (RANS) equations combined with the SST k-ω turbulence model. The Reynolds number used, based on the height of the train and the freestream velocity, is 3.7 × 105. In the results, it was found that variations of the crosswind flow angles produced different flow regimes. Two unique flow regimes appear, representing (i) slender body flow behaviour at a smaller range of Ψ (i.e. Ψ ≤ 45°) and (ii) bluff body flow behaviour at a higher range of Ψ (i.e. Ψ ≥ 60°). As the geometries of the bridge girder were varied, the bridge with the wedge girder showed the worst aerodynamic properties with both important aerodynamic loads (i.e. side force and rolling moment), followed by the triangular girder and the rectangular girder. This was due to the flow separation on the windward side and flow structure formation on the leeward side, both of which are majorly influenced by the flow that moved from the top and below of the bridge structures.
Traffic accidents at night are higher than in other periods, especially on a dark road. This study explores the impact of the dark road on driver behaviours when approaching a parked or slowed-moving vehicle at the front. An experiment was conducted on a racing track at night, with and without road lighting. Different sizes of obstacles were used to represent other vehicles as a lorry, a car, and a motorcycle. The results show that the obstacles can be detected by drivers much earlier with the help of road lighting, and they tend to increase their speed, probably preparing to overtake the obstacles.
15 November 2024 in International Journal of Automotive and Mechanical Engineering
This research explores the application of Proportional-Integral-Derivative (PID) controllers and Variable Steering Ratio (VSR) control strategies within a Steer-by-Wire (SbW) system, utilizing a comprehensive 14 Degrees of Freedom (DOF) full vehicle dynamic model. The study aims to advance vehicle dynamics and control through SbW technology. This research addresses the challenge of optimizing steering control by integrating an SbW system with PID and VSR strategies to overcome the limitations of traditional steering mechanisms and enhance vehicle responsiveness and stability. The SbW system, using a PID-based controller, was rigorously tested and validated using MATLAB Simulink and Hardware-in-the-Loop System (HiLS) method. The performance of the system was assessed through four distinct signal tests: step, sine, square, and sawtooth inputs. These tests confirmed the precision of the PID controller in position tracking. To improve the practical applicability of the SbW system, a 14-DOF vehicle dynamic model was developed and validated before integration with the SbW system. The integrated system accurately replicated conventional steering behavior, as validated by Step Steer Input (SSI) and Double Lane Change (DLC) tests, demonstrating less than 11% RMS percentage error - well within the acceptable threshold of less than 15%. Additionally, the study proposed and validated VSR control strategies through the DLC test. Results indicate that the PID controller effectively tracked desired signals, while the VSR strategy reduced driver workload and improved steering stability. This research offers valuable insights into enhancing SbW system performance and lays a foundation for future advancements in vehicle control systems.
6 December 2022 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
Liquid bulk transport is one of the most important modes of fluid package transport, whether by sea or land. Flexitank has recently attracted the attention of shipment companies as an alternative method of fluid transportation due to the benefits of cost effectiveness, large shipping capacity, environmental friendliness, and quick loading/unloading time. However, the industry reports some cases regarding the leakage of the flexitank during transportation. While the hydrodynamic behaviour of the flexitank during transportation may influence the tank surface leakage issue. Thus, this study aims to determine the suitable filling volume capacity on flexitank by using Computational Fluid Dynamics (CFD). Hydrodynamics performance such as wall shear stress, volume fraction, dynamic pressure, and slosh force will be analyzed on different filling volume capacities and driving cycles. The filling volume capacity analyzed in this study are 5%, 10%, 15% more, or less than the reference capacity, 24000 L, based on different driving cycles: city-suburban and freeway. The results indicate that varying the fill level capacity of the tank affected the liquid sloshing behaviour and hydrodynamic performance of the tank. The highest wall shear stress (WSS) occurs at a filling volume capacity of -15 % because it is increasing the wall shear stress by 80% (city-suburban) and 35% (freeway) than the reference value. Following that, both speed profiles with a +10 % filling volume have the dynamic pressure, reducing it by 60% (city-suburban) and 47% (freeway) compared to the reference value. Thus, the filling volume of +10% is recommended to be suitable for the flexitank. Hence, this study benefits liquid bulk transportation by increasing fill level capacity and optimizing hydrodynamic performance.
The mixing of fuel and air plays a major role in the spray and flame behavior, hence affecting the combustion performance and emissions of the internal mixing air-assisted atomizers. Air-assisted atomizers are introduced to counter the low-pressure differential of a simplex nozzle, which reduces the atomization quality. The present study aims to determine the effects of Multi Circular Jet (MCJ) plates on the geometrical configurations of internal flows in mixing chamber and the internal flow of plate 3 using different properties of fuel. In this study, the realizable k-ε turbulence model, specifically designed for strongly swirling flows, is validated through numerical simulations. The turbulence model selected is a type of Reynolds averaged Navier-Stokes (RANS) model called the k-ε model. The MCJ plates provide the primary air entrance into the mixing chamber. Additionally, it acts as a turbulence generator and can be adjusted to alter the flow of fuel and air mixtures in a mixing chamber. The study compares several MCJ geometries in terms of pressure, speed, turbulent kinetic energy, and volume fraction and compares the performances of diesel and Crude Palm Oil (CPO) B30 biodiesel fuels. The findings imply that CPO B30 biodiesel has superior atomization and mixing due to its higher density and turbulent kinetic energy. CPO B30 biodiesel was compared to Diesel in terms of maximum pressure, average speed, turbulent kinetic energy per unit mass, and volume fraction. The results indicate that CPO B30 has lower pressure and higher velocity than Diesel, suggesting better fuel atomization and mixing. The higher density of CPO B30 leads to increased turbulent kinetic energy, improving fuel-air mixing inside the combustion chamber. The study demonstrates that the use of MCJ plates can enhance mixing in a mixing chamber. In addition, MCJ plates show the ability to control the spray and atomization. The findings of this study contribute to a better understanding of the relationships between geometry and fuel-air mixing, as well as the characteristics of the internal mixing air-assisted atomizer, which will lead to future burner system improvements.