This research explores the application of Proportional-Integral-Derivative (PID) controllers and Variable Steering Ratio (VSR) control strategies within a Steer-by-Wire (SbW) system, utilizing a comprehensive 14 Degrees of Freedom (DOF) full vehicle dynamic model. The study aims to advance vehicle dynamics and control through SbW technology. This research addresses the challenge of optimizing steering control by integrating an SbW system with PID and VSR strategies to overcome the limitations of traditional steering mechanisms and enhance vehicle responsiveness and stability. The SbW system, using a PID-based controller, was rigorously tested and validated using MATLAB Simulink and Hardware-in-the-Loop System (HiLS) method. The performance of the system was assessed through four distinct signal tests: step, sine, square, and sawtooth inputs. These tests confirmed the precision of the PID controller in position tracking. To improve the practical applicability of the SbW system, a 14-DOF vehicle dynamic model was developed and validated before integration with the SbW system. The integrated system accurately replicated conventional steering behavior, as validated by Step Steer Input (SSI) and Double Lane Change (DLC) tests, demonstrating less than 11% RMS percentage error - well within the acceptable threshold of less than 15%. Additionally, the study proposed and validated VSR control strategies through the DLC test. Results indicate that the PID controller effectively tracked desired signals, while the VSR strategy reduced driver workload and improved steering stability. This research offers valuable insights into enhancing SbW system performance and lays a foundation for future advancements in vehicle control systems.
1 September 2025 in International Journal of Automotive and Mechanical Engineering
Steering feel is a crucial factor in Steer-by-Wire (SbW) architecture, where achieving the desired physical feedback is essential for driver experience. This research proposes the application of an adaptive Proportional-Integral (PI)-based controller as a torque tracking algorithm to achieve the targeted steering feel. To support this, a 14-DOF vehicle dynamic model was developed and validated in order to provide the foundation for a torque tracking algorithm to generate steering feel at the steering wheel. In the process of steering feel development, the SbW model was developed using a physical modeling approach based on Newton’s laws, where the steering torque felt by the driver at the wheel corresponds to the torque generated by the rack and pinion assembly. The adaptive tracking torque algorithm is implemented using two methods, which are adaptive PI-based (A-PI) and gain scheduling PI-based (GS-PI) methods. The performance of these controllers was verified by using types of input signals (step and sinusoidal wave) and validated through three vehicle dynamic tests based on the ISO standards, including Double Lane Change, Slalom, and J-Turn tests. The findings showed that the GS-PI controller exhibited significant performance compared to results from the CarSim software, which served as a benchmark. Furthermore, the results indicated that this controller was capable of effectively replicating the desired steering feel with approximately less than 2.5 mean absolute error (MAE). This research study offers a practical control strategy for realistic steering feedback and contributes valuable insight for future SbW development.
This is a preliminary study on the viscosity characteristics of polyalphaolefin (PAO)-based γ-Fe2O3 under zero magnetic fields. By varying the concentration of magnetic nanoparticles (MNPs), PAO-based γ-Fe2O3 with different concentrations were synthesized by co-precipitation method. The effect of this factor on the viscosity characteristic of γ-Fe2O3 (< 30 nm) was investigated on the basic of a series of rheological measurement. The use of oleic acid (OA) as a coating agent and surfactant was also investigated by varying its concentration. The results show the concentration of MNPs and the amount of OA has obvious effect on viscosity characteristics of PAO-based γ-Fe2O3. In the case of comparison between the concentrations of MNPs, higher concentration of MNPs increased the viscosity of the PAO-based γ-Fe2O3 and exhibit nearly Newtonian behavior. The large amount of OA also exhibits the increment on viscosity characteristic of MNPs. The experimental data were compared with the Bingham and Casson model and the results revealed that the rheology of the polyalphaolefin (PAO)-based γ-Fe2O3 fitted the Casson model better.
12 August 2026 in International Journal of Automotive Science And Technology
This study introduces a novel and highly applicable torque tracking algorithm as a controller to develop a realistic steering feel in a front steer-by-wire (SbW) architecture. The objective of this study was to propose a self-tuning PI-based controller using a gain scheduling method to mimic the torque generated by a rack and pinion system through the torque produced by a DC motor. To provide the foundation for the torque tracking control strategy, a full car model with 14 degrees of freedom was developed to assess the efficacy of the proposed control scheme in generating the steering feel. Based on the Newton’s second law, the SbW model was developed and verified using a step input signal in two extreme conditions. The performance of the proposed controller and its robustness were validated through two vehicle dynamic tests based on ISO standard, the Double Lane Change (DLC) and Slalom (SL) tests under varying vehicle speeds and extreme maneuvers. This robustness assessment demonstrates that the gain-scheduling proportional-integral (GS-PI) controller performs significantly well in tracking the desired steering wheel torque, compared to the results from the CarSim software, which served as a benchmark. Additionally, the results indicated that the proposed controller was capable of replicating the steering feel of a conventional steering system with a mean absolute error (MAE) of less than 1.90. This study prepares a platform for practical applications in developing realistic steering feel in future SbW systems. Furthermore, the control proposed in this study provides a practical control system approach suitable for hardware implementation.