31 March 2023 in IEEE Transactions on Components, Packaging and Manufacturing Technology
The electrical contact resistance and thermal contact resistance caused by the actual rough surfaces of parallel groove clamps exist during contact interactions, which affects the heat generation rate and thermal conductivity, and then the accuracy of multi-field coupling numerical simulation. Thus, first, a mechanical-thermal-electrical coupling model of the parallel groove clamp is created based on the improved representation of contact interactions. Then, a progressive sequential coupling method is proposed to improve the calculation accuracy and efficiency of the multi-field coupling. Meanwhile, the validity of the coupling model is verified by electrical resistance and temperature measurement experiments. Finally, the temperature rise characteristic of the parallel groove clamp is analyzed under normal and large current impact conditions. The results show that the experimental and numerical electrical resistance and temperature show a good agreement. The electrical resistance of parallel groove clamps stabilizes when the preload force is greater than the critical value, 5000 N. The highest temperature of parallel groove clamps is always located at the contact edge between the upper clamp block and branch line, and the influence of current intensity on temperature rise is significant under normal condition, while the effect of preload force is less. The large current impact mainly affects the transient temperature rise. However, the effect of the large current impact on steady-state temperature is negligible.
17 August 2022 in International Journal of Thermal Sciences
24 November 2022 in IEEE Transactions on Dielectrics and Electrical Insulation
Electrical contact resistance (ECR) affecting the work behavior is a key index to evaluate the electrical contact capacity of electrical connectors. A large number of factors affecting ECR exist, among which elastoplastic thermal softening (EPTS) caused by temperature rise has a significant effect on ECR. Thus, a high-accuracy dual-iterative coupling method (DICM) is proposed to explore the influence of EPTS on ECR. First, according to the characterization results of the real rough surface, a finite element model (FEM) including a rough surface is created, and the contact state is improved by the contact adjustment method to achieve accurate coupling analysis. Second, the grid dimension is optimized to select an optimal mesh size for the contact surface in terms of computational efficiency and accuracy. Then, a refined numerical model is established. Meanwhile, the validity of the FEM is checked by the experimentally measured ECR. Finally, the impact of EPTS on ECR is revealed through the DICM. The results show that the electrical contact interface suffers from apparent temperature rise due to the Joule heating effect, which causes the ECR to decrease in a different degree under two loading conditions when EPTS is taken into account. Therefore, if a numerical simulation is used to predict the ECR, a DICM should be adopted to obtain more accurate prediction results.
22 February 2022 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Piercing connectors are among the most used equipment in electric circuit. With the continuous development of the electricity industry, higher requirements for the reliability and heat resistance of the piercing connectors are needed. Aiming at the problems of poor current carrying capacity and heat dissipation status, a multifield coupling model of the piercing connector is created to analyze the structural stress and deformation distribution under the action of preload from the bolt and simulate the temperature distribution under different current intensities and surface roughness. Meanwhile, the measured experiments of contact resistance and highest temperature are performed to explore the relationship between contact resistance and the highest temperature. Results show that the maximum stress of the piercing connector is in the contact region between the piercing blade and the wire, which may be the origin of strength failure. The greater the current intensity and surface roughness, the more obvious the temperature rise. The effect of the different specification combinations of power wire and branch wire on contact resistance is small. Moreover, a critical installation torque exists in the influence range. The experimentally measured temperature verifies that the simulation has high precision. In this article, the numerically calculated and experimentally measured results provide a theoretical basis for optimizing the manufacturing and service performance of the piercing connectors.
25 December 2023 in IEEE Transactions on Components, Packaging and Manufacturing Technology
The issue of fretting wear failure of electrical contacts in conductor-parallel groove clamp system might be brought on by breeze vibration. This study discusses the fretting wear behavior of overhead conductor-wire clamp systems in wind-vibration environments and uses energy spectrometry, laser confocal microscopy, and scanning electron microscopy to analyze the wear surfaces and their morphology. The findings indicate an optimal interval for both the electrical contact performance and contact resistance, and that an increase in installation torque leads to a large drop in contact resistance. As serving time increases, the contact interface’s ongoing micromotion degradation will negatively impact the electrical contact performance. The increase in temperature has a significant effect on the micromotion wear.
20 July 2023 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Electrical connectors are widely used in electromechanical equipment. Their rough surfaces inevitably induce electrical contact resistance (ECR) and thermal contact resistance (TCR), which generates a significant influence on electricity and heat conducting at the faying surface and affects the accuracy of the thermal-electrical-mechanical coupling (TEMC) numerical calculation. Thus, a TEMC model with ECR and TCR of a parallel groove clamp is necessary to investigate the TEMC mechanism. Firstly, appropriate ECR and TCR models are created based on the available experimental results. Secondly, a refined TEMC finite element model is established by optimising the mesh size at the faying surfaces, and the cyclic coupling calculation method is adopted to achieve efficient and consistent numerical calculations. Meanwhile, the validity of the simulation model is verified by experimental results. Finally, the transient real contact area, current density, and heat generation rate (HGR) are obtained to analyse the TEMC mechanism during temperature rise. The results indicate that the mechanical characteristics during temperature rise are different under two loading conditions of tight and loose, thereby resulting in different changing laws in terms of the maximum current density and HGR. In addition, two coupling mechanisms exist until the steady-state temperature is achieved.