Samrina Sahir

Samrina Sahir

Auto-generated profile, based on publicly available information

Samrina Sahir

Department of Materials Science and Chemical Engineering, Hanyang University, Ansan 15588, Republic of Korea

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2020 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Closed access
PDF file
KHKwang-Min Han
Kwang-Min Han
SHSo-Young Han
So-Young Han
SSSamrina Sahir
Samrina Sahir
NYNagendra Prasad Yerriboina
Nagendra Prasad Yerriboina
TKTae-Gon Kim
Tae-Gon Kim
JPJin-Goo Park
Jin-Goo Park
The contamination behavior of ceria particles (50 and 100 nm) with oxide surfaces at pH 4 and 8 was studied using dipping and polishing conditions. Higher contamination at pH 4 than pH 8 was observed for dipping cases. In contrast, pH 8 conditions produced higher contamination than pH 4 for polishing cases. The difference in the contamination between dipping and polishing could be attributed to electrostatic attraction and chemical bonding. During polishing, weak or no chemical bonding may occur at pH 4, whereas the Ce–O–Si bond may form due to the surface charges of ceria and silica at pH 8. XPS analysis revealed that strong additional peaks related to Ce–O–Si bonding were detected for O 1s spectra at a binding energy of around 532 eV for surfaces polished at pH 8. Similar results were observed for 50 nm as well as 100 nm ceria particles. Based on the results, we concluded that ceria particles would have different adhesion behaviors for dipping and polishing at the same pH value. Also, higher ceria adhesion was observed at higher pH compared to lower pH during the CMP process, which was correlated to strong Ce–O–Si chemical bond formation due to the CMP conditions.

1 August 2022 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Closed access
PJPalwasha Jalalzai
Palwasha Jalalzai
HRHeon-Yul Ryu
Heon-Yul Ryu
SSSamrina Sahir
Samrina Sahir
RMRanjith Punathil Meethal
Ranjith Punathil Meethal
SHSatomi Hamada
Satomi Hamada
JPJin-Goo Park
Jin-Goo Park
The stability of the cobalt surface after the CMP process is crucial to prevent the corrosion of the surface during the wafer transfer step. The stability of the Co-BTA complex is investigated in this work by using various experimental and surface analysis techniques. The higher inhibition efficiency of the Co-BTA complex observed at pH 7 was further investigated, and a more passive Co surface was observed during the de-ionized water (DIW) rinsing step. The low stability of the Co-BTA complex in the presence of slurry additives was confirmed from the accelerated oxidative dissolution of the Co surface compared to the adsorption of BTA. Ex-situ electrochemical impedance spectroscopy (EIS) was further performed to analyze the stability of the Co-BTA complex to confirm the passivation of Co during the DIW rinsing step. The corrosion resistance of the Co surface during the rinsing step is further enhanced by reducing the dissolved oxygen content.

1 May 2022 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Closed access
PDF file
SSSamrina Sahir
Samrina Sahir
HCHwi-Won Cho
Hwi-Won Cho
PJPalwasha Jalalzai
Palwasha Jalalzai
JPJerome Peter
Jerome Peter
Randeep SinghRandeep Singh
Randeep Singh
JPJin-Goo Park
Jin-Goo Park
The use of polyvinyl acetal (PVA) brushes is one of the most effective and prominent techniques applied for the removal of chemical mechanical planarization (CMP) contaminants. However, the brush can be a source of defects by entrapping the abrasives inside its porous structure during brush scrubbing. In this study, the effect of brush top skin layer was extensively studied on contamination, cross-contamination, and cleaning performance by comparing brushes with and without skin layer. The presence of a dense top skin layer resulted in larger contact areas and high ceria particle adsorption on the skin layer. This leads to higher cross-contamination of the wafers during scrubbing along with high cleaning performances. Conversely, the brushes without skin layer showed lower contamination and negligible cross-contamination with a reduced cleaning performance (removal of ceria particles from oxide surface). Therefore, the role of the brush skin layer is significant and needs to be considered while designing a post-CMP cleaning process.