Eduardo Forniés

Eduardo Forniés

Auto-generated profile, based on publicly available information

Eduardo Forniés

Instituto de Ciencia de Materiales de Madrid (CSIC), E-28049 Cantoblanco, Madrid, Spain

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2005 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Closed access
EFE. Forniés
E. Forniés
CZC. Zaldo
C. Zaldo
JAJ.M. Albella
J.M. Albella

1 May 2006 in Surface and Coatings Technology
Verified
Journal Article
Closed access
EFE. Forniés
E. Forniés
Ramon Escobar-GalindoRamon Escobar-Galindo
Ramon Escobar-Galindo
OGOlga Sánchez Garrido
Olga Sánchez Garrido
JAJ.M. Albella
J.M. Albella

1 November 2013 in Solar Energy
Verified
Journal Article
Closed access
EFEduardo Forniés
Eduardo Forniés
FNFernando Naranjo
Fernando Naranjo
MMManuel Mazo
Manuel Mazo
FRFernando Ruiz
Fernando Ruiz

11 July 2005 in Journal of Analytical Atomic Spectrometry
Verified
Journal Article
Closed access
PDF file
Ramon Escobar-GalindoRamon Escobar-Galindo
Ramon Escobar-Galindo
EFE. Forniés
E. Forniés
JAJ. M. Albella
J. M. Albella
In depth profile analysis by radio-frequency glow discharge optical emission spectroscopy (rf-GDOES) techniques, the depth resolution mainly depends on the roughening induced during the sputtering and the resulting crater geometry. In this work we have tried to isolate the contributions of the different effects that degrade the depth resolution in GDOES analysis of metal coatings deposited on silicon substrates. First, the existence of an edge well around the crater (“edge effect”), deeper than the crater bottom, results in an initial rise of the quantified profile of the bottom layer before reaching the interface. A second effect is the induced roughening of the crater bottom, which produces a broadening of the interface width. Finally, we have explained the long tails observed after crossing the interface in the metal profiles in terms of the sputtering of material re-deposited at the crater wall. The importance of these effects was tested for the particular case of multilayer stacks consisting of alternating chromium and titanium layers of different thicknesses. Reversing the order of the layers showed the influence of different sputtering rates of the materials in the depth profile. The profiles of materials with high sputtering rate (i.e., chromium in this study) become less affected than material with low sputtering rate (titanium) due to lower mixing of the layers.

20 June 2006 in Surface and Coatings Technology
Verified
Journal Article
Closed access
Ramon Escobar-GalindoRamon Escobar-Galindo
Ramon Escobar-Galindo
EFE. Forniés
E. Forniés
JAJ.M. Albella
J.M. Albella

21 September 2005 in Journal of Analytical Atomic Spectrometry
Verified
Journal Article
Closed access
PDF file
Ramon Escobar-GalindoRamon Escobar-Galindo
Ramon Escobar-Galindo
EFE. Forniés
E. Forniés
JAJ. M. Albella
J. M. Albella
The crater shape effects in GDOES depth profiling of multilayer metal coatings, with an individual thickness layer >500 nm, studied in the foregoing paper, have been extended to the case of thinner layers (layer thickness <150 nm). The analysis of 10 bilayers of 70 nm chromium and 150 nm titanium showed an increased degradation of the composition depth profiles. The continuous change in shape of the crater after each interface induces a higher mixing of the thin layers. Reducing the thickness of the individual layers added new features to the depth profiles, such as changes on the symmetry of the profiles probably due to a mixing or simultaneous detection of consecutive bilayers. Ultra-thin chromium layers of 2.5 and 5 nm, buried at different depths in a titanium matrix up to a thickness of 3 µm, were properly resolved both near the surface and deeply embedded in the matrix and used to evaluate the depth resolution function of the GDOES technique. The relative depth resolutions of all the interfaces were estimated showing a typical dependence with depth (z) of the type z−0.6–0.7.