Wei Lu

Wei Lu

Auto-generated profile, based on publicly available information

Wei Lu

School of Mechanical and Automotive Engineering, Qingdao University of Technology, Qingdao 266520, P. R. China

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 October 2021 in Transactions of the Institute of Measurement and Control
Verified
Journal Article
Closed access
PDF file
WLWei Lu
Wei Lu
CZChengguo Zong
Chengguo Zong
JLJinliang Li
Jinliang Li
DLDejian Liu
Dejian Liu
This paper considers a multi-robot formation control scheme for high-order bipartite consensus under time-varying delays. First, a third-order bipartite consensus protocol under time-varying delays is presented, and then a high-order bipartite consensus protocol is extended from it. Then, necessary and sufficient conditions for third-order and high-order multi-agent systems without time-delays are given to attain bipartite consensus following the protocols. Communication time-delays are added to the protocols, and the theory of Lyapunov asymptotic stability is used to obtain sufficient conditions for the multi-agent systems with communication delays to ultimately attain a bipartite consensus. Furthermore, the given protocol is employed for the formation control of multi-robot systems, and a formation control scheme for multi-robot systems with time-varying delays is proposed. Finally, a few simulations are implemented to demonstrate the rationality and availability of the method.

6 December 2024 in Journal of Advanced Manufacturing Systems
Verified
Journal Article
Closed access
WLWei Lu
Wei Lu
Youqiang WangYouqiang Wang
Youqiang Wang
Chenbing NiChenbing Ni
Chenbing Ni
CZChengguo Zong
Chengguo Zong
LLLongxiang Liu
Longxiang Liu
BZBaoguo Zhang
Baoguo Zhang

9 August 2022 in Research Square
Verified
Preprint
Open access
PDF file
WLWei Lu
Wei Lu
CZChengguo Zong
Chengguo Zong
CNChenbing Ni
Chenbing Ni
XYXiao Yu
Xiao Yu
DLDejian Liu
Dejian Liu
This paper investigates the effect of crystal orientations and machining parameters on the surface integrity of 7050 aluminum alloy in high-speed machining. Three groups of pre-compression deformations (10%, 15%, and 20%) are performed on the aluminum alloy to fabricate specimens with different crystal orientations. A single-factor dry cutting experiment was designed, and the surface roughness, surface morphology and defects, work hardening, and X-ray diffraction (XRD) were tested. The results show that the 15% pre-deformed 7050 aluminum alloy specimen had lower surface roughness and the best surface quality under the same cutting parameters. The surface roughness of 7050 aluminum alloy with different crystal orientations tended to first increase and then decrease with the increase of the cutting speed, and the surface roughness was positively correlated with the cutting depth and feed rate. Under different cutting parameters, the machined surfaces of 7050 aluminum alloy specimens with different crystal orientations exhibited different degrees of plowings, apophysis, sticky chips and pits. Moreover, the degree of work hardening of the 15% pre-deformed 7050 aluminum alloy specimen was small, while that of the 20% pre-deformed specimen was more serious. XRD analysis demonstrated that the diffraction peak width of the 10% pre-deformed 7050 aluminum alloy specimen slightly increased with the increase of the cutting depth. Moreover, the (111) and (200) diffraction peak intensities of the 15% pre-deformed 7050 aluminum alloy specimen increased with the increase of the cutting speed, and there was no obvious Al 2 CuMg phase on the machined surface of the 20% pre-deformed specimen.

15 November 2025 in Journal of Advanced Manufacturing Systems
Verified
Journal Article
Closed access
BZBaoguo Zhang
Baoguo Zhang
LLLongxiang Liu
Longxiang Liu
Chenbing NiChenbing Ni
Chenbing Ni
Youqiang WangYouqiang Wang
Youqiang Wang
DLDejian Liu
Dejian Liu
WLWei Lu
Wei Lu