Torsten Rabe

Torsten Rabe

Auto-generated profile, based on publicly available information

Torsten Rabe

Division Advanced Technical Ceramics, Bundesanstalt fuer Materialforschung und -pruefung BAM 1 , 12200 Berlin, Germany

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 August 2019 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
SBSophie Bresch
Sophie Bresch
BMBjoern Mieller
Bjoern Mieller
DSDaniela Schoenauer-Kamin
Daniela Schoenauer-Kamin
Ralf MoosRalf Moos
Ralf Moos
FGFabien Giovanelli
Fabien Giovanelli
TRTorsten Rabe
Torsten Rabe
Calcium cobaltite (Ca3Co4O9) is considered as one of the most promising thermoelectric p-type oxides for energy harvesting applications at temperatures above 500 °C. It is challenging to sinter this material as its stability is limited to 920 °C. To facilitate a practicable and scalable production of Ca3Co4O9 for multilayer generators, a systematic study of the influence of powder calcination, Bi doping, reaction sintering, and pressure-assisted sintering (PAS) on microstructure and thermoelectric properties is presented. Batches of doped, undoped, calcined, and not calcined powders were prepared, tape-cast, and sintered with and without uniaxial pressure at 900 °C. The resulting phase compositions, microstructures, and thermoelectric properties were analyzed. It is shown that the beneficial effect of Bi doping observed on pressureless sintered samples cannot be transferred to PAS. Liquid phase formation induces distortions and abnormal grain growth. Although the Seebeck coefficient is increased to 139 μV/K by Bi doping, the power factor is low due to poor electrical conductivity. The best results were achieved by PAS of calcined powder. The dense and textured microstructure exhibits a high power factor of 326 μW/m K2 at 800 °C but adversely high thermal conductivity in the relevant direction. The figure of merit is higher than 0.08 at 700 °C.

6 September 2012 in Particle & Particle Systems Characterization
Verified
Journal Article
Open access
PDF file
PKPetra Kuchenbecker
Petra Kuchenbecker
MGMarion Gemeinert
Marion Gemeinert
TRTorsten Rabe
Torsten Rabe
Presented are results of an inter‐laboratory study (ILS) for measurements of the particle size distribution of fine powders in wet dispersion by laser diffraction. In this proficiency test 32 participants from four countries took part. They utilized 13 different devices from 7 manufacturers.Three commercial powders (glass spheres and two silicon carbide powders) showing a median diameter of about 30, 10 and 1 μm (volume distribution), respectively, were chosen for the procedure. A homogeneity study was carried out after the units had been separated and bottled.All participants received their test samples including a description of the standard operating procedures based on ISO 13320:2009 – to ensure that experiments were performed in a consistent manner. Results were calculated using the Mie Theory. The general means and the precision of the results were estimated in accordance with ISO 5725‐2:2002.The evaluation showed excellent values of repeatability standard deviation. Values of 4 to 21 % of the reproducibility standard deviation of the results were found in the particle size range above 1 μm. Much larger deviation between the labs was detected in the case of smaller particles. Differences in the design of the analyzers were unambiguously identified as the main reason for the large deviations.

1 May 2021 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
AHAli Hajian
Ali Hajian
TKThomas Konegger
Thomas Konegger
KBKonrad Bielecki
Konrad Bielecki
BMBjoern Mieller
Bjoern Mieller
TRTorsten Rabe
Torsten Rabe
USUlrich Schmid
Ulrich Schmid

20 April 2017 in International Journal of Applied Ceramic Technology
Verified
Journal Article
Closed access
PDF file
CKChristian Kohler
Christian Kohler
MNMohammad Nikfalazar
Mohammad Nikfalazar
AHAndreas Heunisch
Andreas Heunisch
BSBärbel Schulz
Bärbel Schulz
MMMorten Mikolajek
Morten Mikolajek
JBJoachim R. Binder
Joachim R. Binder

1 September 2015 in Additional Conferences (Device Packaging, Hitec, Hiten, & Cicmt)
Verified
Journal Article
Closed access
AHAndreas Heunisch
Andreas Heunisch
VSVictor de Seauve
Victor de Seauve
TRTorsten Rabe
Torsten Rabe
In this work, the effect of the pressure-assisted sintering process on buried thick film resistors integrated in LTCC multilayer has been studied. Four commercial resistor pastes with sheet resistivities between 10 kΩ and 10 MΩ/cm were analyzed. First they were characterized by SEM/EDX, XRD and Laser diffraction to determine composition and particle distribution. The pastes consist of isolating particles and of Ruthenium based particles that are supposed to build the conductive phase. The pastes were screen printed on LTCC green tape (DP 951) and buried in four layer laminates. Sintering was done in two ways, pressureless (PLS) and also pressure-assisted (PAS). The pressureless sintered resistors showed electrical resistance values roughly in the range of the nominal sheet resistivity and only relatively small fluctuation within one sample. The PAS samples on the other hand showed significantly higher resistances and larger deviations. The microstructure of the sintered resistors was again investigated by SEM and XRD. It seems that the resistivity is determined by the ratio of the two Ruthenium phases RuO2 and Pb2Ru2O6.5, where RuO2 has the higher conductivity. Buried resistors cannot be trimmed by a laser to adjust the resistance. But we discovered that a refiring step will reduce and normalize the resistivity of the PAS resistors significantly.