Sophie Bresch

Sophie Bresch

Auto-generated profile, based on publicly available information

Sophie Bresch

Department 5 – Materials Engineering Bundesanstalt für Materialforschung und ‐prüfung (BAM) Unter den Eichen 87 12205 Berlin Germany

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 October 2020 in Journal of the American Ceramic Society
Verified
Journal Article
Open access
PDF file
SBSophie Bresch
Sophie Bresch
BMBjörn Mieller
Björn Mieller
DSDaniela Schönauer‐Kamin
Daniela Schönauer‐Kamin
Ralf MoosRalf Moos
Ralf Moos
TRTimmy Reimann
Timmy Reimann
TRTorsten Rabe
Torsten Rabe
Calcium cobaltite Ca 3 Co 4 O 9 , abbreviated Co349, is a promising thermoelectric material for high‐temperature applications in air. Its anisotropic properties can be assigned to polycrystalline parts by texturing. Tape casting and pressure‐assisted sintering (PAS) are a possible future way for a cost‐effective mass‐production of thermoelectric generators. This study examines the influence of pressure and dwell time during PAS at 900°C of tape‐cast Co349 on texture and thermoelectric properties. Tape casting aligns lentoid Co349. PAS results in a textured Co349 microstructure with the thermoelectrically favorable ab‐direction perpendicular to the pressing direction. By pressure variation during sintering, the microstructure of Co349 can be tailored either toward a maximum figure of merit as required for energy harvesting or toward a maximum power factor as required for energy harvesting. Moderate pressure of 2.5 MPa results in 25% porosity and a textured microstructure with a figure of merit of 0.13 at 700°C, two times higher than the dry‐pressed, pressureless‐sintered reference. A pressure of 7.5 MPa leads to 94% density and a high power factor of 326 µW/mK 2 at 800°C, which is 11 times higher than the dry‐pressed reference (30 MPa) from the same powder.

15 August 2019 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
SBSophie Bresch
Sophie Bresch
BMBjoern Mieller
Bjoern Mieller
DSDaniela Schoenauer-Kamin
Daniela Schoenauer-Kamin
Ralf MoosRalf Moos
Ralf Moos
FGFabien Giovanelli
Fabien Giovanelli
TRTorsten Rabe
Torsten Rabe
Calcium cobaltite (Ca3Co4O9) is considered as one of the most promising thermoelectric p-type oxides for energy harvesting applications at temperatures above 500 °C. It is challenging to sinter this material as its stability is limited to 920 °C. To facilitate a practicable and scalable production of Ca3Co4O9 for multilayer generators, a systematic study of the influence of powder calcination, Bi doping, reaction sintering, and pressure-assisted sintering (PAS) on microstructure and thermoelectric properties is presented. Batches of doped, undoped, calcined, and not calcined powders were prepared, tape-cast, and sintered with and without uniaxial pressure at 900 °C. The resulting phase compositions, microstructures, and thermoelectric properties were analyzed. It is shown that the beneficial effect of Bi doping observed on pressureless sintered samples cannot be transferred to PAS. Liquid phase formation induces distortions and abnormal grain growth. Although the Seebeck coefficient is increased to 139 μV/K by Bi doping, the power factor is low due to poor electrical conductivity. The best results were achieved by PAS of calcined powder. The dense and textured microstructure exhibits a high power factor of 326 μW/m K2 at 800 °C but adversely high thermal conductivity in the relevant direction. The figure of merit is higher than 0.08 at 700 °C.

27 February 2018 in Journal of Electroceramics
Verified
Journal Article
Closed access
PDF file
SBSophie Bresch
Sophie Bresch
BMBjörn Mieller
Björn Mieller
CSChristian Selleng
Christian Selleng
TSThomas Stöcker
Thomas Stöcker
Ralf MoosRalf Moos
Ralf Moos
TRTorsten Rabe
Torsten Rabe

15 November 2021 in Journal of the American Ceramic Society
Verified
Journal Article
Open access
PDF file
SBSophie Bresch
Sophie Bresch
BMBjörn Mieller
Björn Mieller
PMPaul Mrkwitschka
Paul Mrkwitschka
Ralf MoosRalf Moos
Ralf Moos
TRTorsten Rabe
Torsten Rabe
Thermoelectric generators can be used as energy harvesters for sensor applications. Adapting the ceramic multilayer technology, their production can be highly automated. In such multilayer thermoelectric generators, the electrical insulation material, which separates the thermoelectric legs, is crucial for the performance of the device. The insulation material should be adapted to the thermoelectric regarding its averaged coefficient of thermal expansion α and its sintering temperature while maintaining a high resistivity. In this study, starting from theoretical calculations, a glass‐ceramic composite material adapted for multilayer generators from calcium manganate and calcium cobaltite is developed. The material is optimized towards an α of 11 × 10 −6 K −1 (20–500°C), a sintering temperature of 900°C, and a high resistivity up to 800°C. Calculated and measured α are in good agreement. The chosen glass‐ceramic composite with 45 vol.% quartz has a resistivity of 1 × 10 7 Ωcm and an open porosity of <3%. Sintered multilayer samples from tape‐cast thermoelectric oxides and screen‐printed insulation show only small reaction layers. It can be concluded that glass‐ceramic composites are a well‐suited material class for insulation layers as their physical properties can be tuned by varying glass composition or dispersion phases.

1 August 2022 in AIP Advances
Verified
Journal Article
Open access
PDF file
SBSophie Bresch
Sophie Bresch
BMBjörn Mieller
Björn Mieller
Ralf MoosRalf Moos
Ralf Moos
TRTorsten Rabe
Torsten Rabe
This study combines three different approaches to lower the sintering temperature of Sm-doped CaMnO3 to save energy in production and facilitate co-firing with other low-firing oxides or metallization. The surface energy of the powder was increased by fine milling, sintering kinetics were enhanced by additives, and uniaxial pressure during sintering was applied. The shrinkage, density, microstructure, and thermoelectric properties were evaluated. Compared to micro-sized powder, the use of finely ground powder allows us to lower the sintering temperature by 150 K without reduction of the power factor. By screening the effect of various common additives on linear shrinkage of CaMnO3 after sintering at 1100°C for 2 h, CuO is identified as the most effective additive. Densification at sintering temperatures below 1000°C can be significantly increased by pressure-assisted sintering. The power factor at room temperature of CaMnO3 nano-powder sintered at 1250°C was 445 μW/(m K2). Sintering at 1100°C reduced the power factor to 130 μW/(m K2) for CaMnO3 nano-powder, while addition of 4 wt. % CuO to the same powder led to ∼290 μW/(m K2). The combination of fine milling, CuO addition, and pressure-assisted sintering at 950°C resulted in a power factor of ∼130 μW/(m K2). These results show that nano-sized powder and CuO addition are successful and recommendable strategies to produce CaMnO3 with competitive properties at significantly reduced temperatures and dwell times.

19 December 2023 in Advanced Electronic Materials
Verified
Journal Article
Open access
SBSophie Bresch
Sophie Bresch
PSPatrick Stargardt
Patrick Stargardt
Ralf MoosRalf Moos
Ralf Moos
BMBjörn Mieller
Björn Mieller
Thermoelectric generators are very attractive devices for waste heat energy harvesting as they transform a temperature difference into electrical power. However, commercially available generators show poor power density and limited operation temperatures. Research focuses on high‐temperature materials and innovative generator designs. Finding the optimal design for a given material system is challenging. Here, a theoretical framework is provided that allows appropriate generator design selection based on the particular material properties. For high‐temperature thermoelectric oxides, it can be clearly deduced that unileg multilayer generators have the highest potential for effective energy harvesting. Based on these considerations, prototype unileg multilayer generators from the currently best thermoelectric oxide Ca3Co4O9 are manufactured for the first time by industrially established ceramic multilayer technology. These generators exhibit a power density of 2.2 mW cm−2 at a temperature difference of 260 K, matching simulated values and confirming the suitability of the technology. Further design improvements increase the power density by a factor of 22 to facilitate practicable power output at temperature differences as low as 7 K. This work demonstrates that reasonable energy harvesting at elevated temperatures is possible with oxide materials and appropriate multilayer design.