2 September 2024 in Applied Physics Letters
Rutile germanium dioxide (r-GeO2) has been identified as an ultrawide bandgap semiconductor recently, featuring a bandgap of 4.68 eV—comparable to Ga2O3—but offering bipolar dopability, higher electron mobility, higher thermal conductivity, and higher Baliga figure of merit (BFOM). These superior properties position GeO2 as a promising material for various semiconductor applications. However, the epitaxial growth of r-GeO2, particularly in its most advantageous rutile polymorph, is still at an early stage. This work explores the growth of r-GeO2 using metal-organic chemical vapor deposition (MOCVD) on an r-TiO2 (001) substrate, utilizing tetraethyl germane as the precursor. Our investigations reveal that higher growth temperatures significantly enhance crystalline quality, achieving a full width at half maximum of 0.181° at 925 °C, compared to 0.54° at 840 °C and amorphous structures at 725 °C. Additionally, we found that longer growth durations increase surface roughness due to the formation of faceted crystals. Meanwhile, adjusting the susceptor rotation speed from 300 to 170 RPM plays a crucial role in optimizing crystalline quality, effectively reducing surface roughness by approximately 15 times. This study offers a foundational guide for optimizing MOCVD growth conditions of r-GeO2 films, emphasizing the crucial need for precise control over deposition temperature and rotation speed to enhance adatom mobility and effectively minimize the boundary layer thickness.
26 May 2025 in Applied Physics Letters
Ultrawide bandgap semiconductors are promising for the next-generation power electronics, largely attributed to their substantial bandgap and exceptional breakdown electric field. Rutile GeO2 (r-GeO2) emerges as a promising alternative, particularly because of its ambipolar dopability. However, research on r-GeO2 is still in its infancy, and further investigation into its structural properties is essential for enhancing epilayer quality. In our previous work, we identified distinct surface morphologies—square-patterned and smooth regions—of r-GeO2 films grown on r-TiO2 (001) substrates using metal-organic chemical vapor deposition. This research employs transmission electron microscopy to investigate the structural characteristics of the material. The findings indicate that the square-patterned regions are crystalline, whereas the smooth regions exhibit amorphous properties. The measured lattice spacing in the (110) plane is 0.324 nm, slightly exceeding the theoretical value of 0.312 nm. This discrepancy suggests the presence of tensile strain in the r-GeO2 film, resulting from lattice mismatch or thermal expansion differences with the substrate. We also observed a threading dislocation density of 1.83 × 109 cm−2, consisting of 11.76% screw-type, 29.41% edge-type, 55.89% mixed-type dislocations, and 2.94% planar defects. These findings offer valuable insight into the growth mechanisms and defect characteristics of r-GeO2.
4 September 2025 in IEEE Transactions on Electron Devices
Ga2O3 Schottky barrier diodes (SBDs) featuring a field plate (FP) and a composite SiO2/SiNx dielectric layer beneath the FP were fabricated, achieving a breakdown voltage (BV) of 2.4 kV at room temperature (RT). Electrical performance and degradation were analyzed via I–V and C–V measurements from 25 °C to 500 °C, revealing temperature-dependent transport, interface stability, and device stability. Upon returning to RT, the diodes exhibited nearly unchanged forward characteristics, while the BV declined significantly from 2.4 kV to 700 V. This behavior indicates a temperature-induced reduction in the barrier height. The detailed analysis revealed that variable range hopping (VRH) dominated the leakage mechanism at moderate temperatures, while thermal emission (TE) became increasingly significant at temperatures exceeding 400 °C.
23 April 2021 in IEEE Sensors Journal
Unexpected results have been seen in multiple papers involving spread spectrum time domain reflectometry (SSTDR) measurements on twin lead cables with one line containing a fault. A small portion of the signal is able to transmit past the fault, reflect off the end of the cable, return back through the fault, and be recorded by the SSTDR. This paper explains the physics of why this can happen, and the effect of nearby ground planes. The transmission through the fault involves electric and magnetic fields coupling to nearby conductive objects. This coupling allows for a small amount of signal to move beyond the fault. We use multi-conductor transmission line theory to explain this effect. A finite difference time domain simulation of the multi-conductor system is compared to measured results to demonstrate why this effect occurs, and the effect of the nearby ground.
5 October 2020 in IEEE Journal of Photovoltaics
The ability of spread spectrum time domain reflectometry (SSTDR) to detect and locate faults in photovoltaic (PV) systems is considered in this article. This article provides a simulation that could be used for studying how faults and other parameters affect the reflectometry response and evaluating fault detection algorithms, for providing comparison simulations in iterative inversion algorithms used to detect and locate faults, or it could potentially be used to replace the measured baseline for these algorithms. The simulation uses an enhanced systematic solution procedure to find the reflection signature of the PV system, and is capable of modeling elements with complex impedance in both series and parallel separated by transmission lines. This article is an expansion of previous work to be capable of simulating systems containing n number of elements (such as PV panels and transmission lines) in series or parallel. The simulation was tested for 20 systems containing up to four resistors, capacitors, and PV cells, and was compared to the measured data.