Teuvo Maunula

Teuvo Maunula

Auto-generated profile, based on publicly available information

Teuvo Maunula

Dinex Finland Oy, Global Catalyst Competence Centre, P.O. Box 20, FI-41331 Vihtavuori, Finland

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
KLKati Lehtoranta
Kati Lehtoranta
PKPäivi Koponen
Päivi Koponen
HVHannu Vesala
Hannu Vesala
KKKauko Kallinen
Kauko Kallinen
TMTeuvo Maunula
Teuvo Maunula
Liquefied natural gas (LNG) use as marine fuel is increasing. Switching diesel to LNG in ships significantly reduces air pollutants but the methane slip from gas engines can in the worst case outweigh the CO2 decrease with an unintended effect on climate. In this study, a methane oxidation catalyst (MOC) is investigated with engine experiments in lean-burn conditions. Since the highly efficient catalyst needed to oxidize methane is very sensitive to sulfur poisoning a regeneration using stoichiometric conditions was studied to reactivate the catalyst. In addition, the effect of a special sulfur trap to protect the MOC and ensure long-term performance for methane oxidation was studied. MOC was found to decrease the methane emission up to 70–80% at the exhaust temperature of 550 degrees. This efficiency decreased within time, but the regeneration done once a day was found to recover the efficiency. Moreover, the sulfur trap studied with MOC was shown to protect the MOC against sulfur poisoning to some extent. These results give indication of the possible use of MOC in LNG ships to control methane slip emissions.

9 October 2020 in Emission Control Science and Technology
Verified
Journal Article
Closed access
PDF file
TMT. Maunula
T. Maunula
MTM. Tuikka
M. Tuikka
TWT. Wolff
T. Wolff

27 February 2018 in ChemCatChem
Verified
Journal Article
Open access
PDF file
NKNiko Kinnunen
Niko Kinnunen
MKMatthew Keenan
Matthew Keenan
KKKauko Kallinen
Kauko Kallinen
TMTeuvo Maunula
Teuvo Maunula
MSMika Suvanto
Mika Suvanto
Catalytic combustion of methane, the main component of natural gas, is a challenge under lean‐burn conditions and at low temperatures owing to sulfur poisoning of the Pd‐rich catalyst. This paper introduces a more sulfur‐resistant catalyst system that can be regenerated during operation. The developed catalyst system lowers the barrier that has restrained the use of liquefied natural gas as a fuel in energy production.

5 May 2016 in Topics in Catalysis
Verified
Journal Article
Closed access
PDF file
TMT. Maunula
T. Maunula
KKK. Kallinen
K. Kallinen
ASA. Savimäki
A. Savimäki
TWT. Wolff
T. Wolff

8 May 2019 in Catalysts
Verified
Journal Article
Open access
PDF file
NKNiko Kinnunen
Niko Kinnunen
VNVille H. Nissinen
Ville H. Nissinen
JHJanne Hirvi
Janne Hirvi
KKKauko Kallinen
Kauko Kallinen
TMTeuvo Maunula
Teuvo Maunula
MSMika Suvanto
Mika Suvanto
Exhaust gas aftertreatment systems play a key role in controlling transportation greenhouse gas emissions. Modern aftertreatment systems, often based on Pd metal supported on aluminum oxide, provide high catalytic activity but are vulnerable to sulfur poisoning due to formation of inactive sulfate species. This paper focuses on regeneration of Pd-based catalyst via the decomposition of alumina-supported aluminum and palladium sulfates existing both individually and in combination. Decomposition experiments were carried out under hydrogen (10% H2/Ar), helium (He), low oxygen (0.1% O2/He), and excess oxygen (10% O2/He). The structure and composition of the model catalysts were examined before and after the decomposition reactions via powder X-ray diffraction and elemental sulfur analysis. The study revealed that individual alumina-supported aluminum sulfate decomposed at a higher temperature compared to individual alumina-supported palladium sulfate. The simultaneous presence of aluminum and palladium sulfates on the alumina support decreased their decomposition temperatures and led to a higher amount of metallic palladium than in the corresponding case of individual supported palladium sulfate. From a fundamental point of view, the lowest decomposition temperature was achieved in the presence of hydrogen gas, which is the optimal decomposition atmosphere among the studied conditions. In summary, aluminum sulfate has a two-fold role in the regeneration of a catalyst—it decreases the Pd sulfate decomposition temperature and hinders re-oxidation of less-active metallic palladium to active palladium oxide.

8 April 2013 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
TMTeuvo Maunula
Teuvo Maunula
Stricter emission limitations for NOx and particulates in mobile applications will require the use of active aftertreatment methods like Diesel Particulate Filters (DPF), Selective Catalytic Reduction (SCR) with urea and Lean NOx Trap (LNT) as combinations in the 2010's. Due to the significant total space and required investments, a lot of efforts have been focused recently on the optimization of the combinatory aftertreatment systems (ATS).In this study the possibilities to intensify the catalytic ATS were analyzed and reviewed by the examples and studies with engines, laboratory reactors and simulations. The focus was on diesel applications, where the number of needed ATS units is the widest. The diesel engine modifications on SCR or EGR engines have to be also designed together with ATS. The intensification includes the principles of down-sizing and the integration of ATS units with control systems. The reaction engineering of catalytic reaction and regenerations (DPF, LNT) was also analyzed. The intensification covered the examples about the integration of DOC, LNT and SCR on DPF, high cell density substrates (metallic) and the integration of hydrolysis and ammonia slip catalysis on the SCR unit. The intensification cases were analyzed by the observed catalytic activities, pressure drop, the volume of systems and costs. The LNT coating on DPF gave a promising possibility to integrate PM, nitrate and sulfate regeneration methods and OBD. The integration of control units and their functions is also a modern way to keep emissions, complexity and costs low.The use of natural gas as fuel results in low PM emissions and no DPF is needed in Euro 6. However, the intensification of ATS may result in a stoichiometric engine with a three-way catalyst instead of a lean combustion engine with oxidation and SCR catalysts in heavy-duty natural gas applications.