18 April 2018 in ACS Photonics
19 May 2020 in ACS Photonics
10 September 2019 in Nanoscale
Tamm plasmonic (TP) structures, consisting of a metallic film and a distributed Bragg reflector (DBR), can exhibit pronounced light confinement allowing for enhanced absorption in the metallic film at the wavelength of the TP resonance. This wavelength dependent absorption can be converted into an electrical signal through the internal photoemission of energetic hot-electrons from the metallic film. Here, by replacing the metallic film at the top of a TP structure with a hot-electron device in a metal–semiconductor–ITO (M–S–ITO) configuration, for the first time, we experimentally demonstrate a wavelength-selective photoresponse around the telecommunication wavelength of 1550 nm. The M–S–ITO junction is deliberately designed to have a low energy barrier and asymmetrical hot-electron generation, in order to guarantee a measurable net photocurrent even for sub-bandgap incident light with a photon energy of 0.8 eV (1550 nm). Due to the excitation of TPs between the metallic film in the M–S–ITO structure and the underlying DBR, the fabricated TP coupled hot-electron photodetector exhibits a sharp reflectance dip with a bandwidth of 43 nm at a wavelength of 1581 nm. The photoresponse matches the absorptance spectrum, with a maximum value of 8.26 nA mW−1 at the absorptance peak wavelength that decreases by more than 80% when the illumination wavelength is varied by only 52 nm (from 1581 to 1529 nm), thus realizing a high modulation wavelength-selective photodetector. This study demonstrates a high-performance, lithography-free, and wavelength-selective hot-electron near-infrared photodetector using an M–S–ITO–DBR planar structure.
19 April 2021 in Advanced Functional Materials
15 October 2018 in Applied Physics Letters
Tamm plasmons (TPs), which exist at the interface between a metallic film and a distributed Bragg reflector (DBR), can be thermally excited and then out-coupled as thermal radiation, providing a means to realize easy-to-fabricate and wavelength-selective infrared emitters. A modified TP structure consisting of a DBR having a thick layer adjacent to the metallic film is proposed and high-intensity and narrowband thermal emission of the structure is demonstrated. The modified TP structure sustains a higher order TP mode with a higher quality factor (Q-factor) emittance peak than a standard TP structure. The measurement of the emission at 150 °C of the proposed TP structure reveals an emittance peak with a maximum value of 0.94, a background of 0.01, and a Q-factor of 48 at a wavelength around 5 μm. Moreover, a wide range of emission wavelengths (from 4.4 μm to 5.7 μm) is experimentally realized by adjusting the last DBR-layer thickness, thus demonstrating a fine selection of the emission peak wavelength.
26 August 2019 in Applied Physics Letters
A Bloch surface wave (BSW) platform opens up new possibilities in the design of sensors and components for photonic circuits owing to its superior properties such as low propagation losses that enable long optical communication lengths and large surface sensing areas. However, most of the reported BSW platforms require a large number of alternating layers to realize the coupling of the surface wave mode. Additionally, although BSW modes have been investigated in the visible region and the near-infrared (NIR) region, only limited reports are available in the important mid-infrared (MIR) region. In this study, we demonstrated a BSW platform consisting of only two Ge/SiO2 pairs and realizing well-coupled BSW in a wide spectral range from the NIR to the MIR. Exploiting the large refractive index difference between Ge and SiO2, the proposed BSW multilayer structure is designed to possess only two pairs of layers with a smaller total thickness than any of the reported BSW platforms. The reported MIR BSW mode shows potential for determination of trace elements and molecule species attached on the surface of the proposed BSW structure.