15 April 2024 in Applied Physics Letters
AlGaN multiple-quantum-well diode-based solar-blind ultraviolet emission-detection monolithic integration system shows great application value due to its advantages of multifunctionality, secure communication, and anti-interference ability. To reduce the lateral optical propagation loss and improve the emitting light detection efficiency, we have proposed a concentric ring-circle configuration for the system, where the out-ring light-emitting diode is the emitter at 253 and 267 nm, and the inner-circle detector is the receiver. The out-ring light-emitting diode exhibits about twice the injection current at the same bias and slightly higher light output power at the same current due to better current spreading and sidewall light extraction compared to the conventional square–square configuration. Simultaneously, the concentric inner-circle detector maximizes the collection of the emitted light flux. Under the emission-detection mode for the monolithic integration system, compared to the conventional square–square configuration, the concentric ring-circle design presents an improvement in the ratio of emitter injection current to detector output photocurrent and higher output signal amplitude under the same transmission work mode, demonstrating the improved system energy and coupling efficiency. This design provides a potential approach to achieve low power consumption and high bandwidth in the monolithic integrated optoelectronic chips.
12 July 2024 in Optics Letters
In this work, we propose a highly reflective Ni/Pt/Al p-electrode for AlGaN-based deep ultraviolet (DUV) light-emitting diodes (LEDs) with a wavelength of 276 nm. AlGaN-based DUV LEDs with traditional Al-based reflectivity electrodes suffer from device degradation and wall-plug efficiency (WPE) droop due to the Al diffusion during electrode annealing. By inserting a Pt layer between the Ni contact layer and the Al reflective layer, the contact characteristics of the p-electrode can be optimized by blocking the diffusion of the O and Al atoms, maintaining a high reflectivity of over 80% near 280 nm. Compared to the AlGaN-based DUV LEDs with Ni/Au traditional p-electrodes and Ni/Al traditional reflective p-electrodes, the WPE of the LED with a highly reflective Ni/Pt/Al p-electrode is improved by 10.3% and 30.5%, respectively. Besides, compared to the other novel reflective p-electrodes using multiple annealing or evaporation processes reported for the AlGaN-based DUV LEDs, we provide a new, to the best of our knowledge, optimization method for single evaporation and annealing p-type reflective electrodes, featured with a simpler and more convenient process flow.
11 December 2025 in ACS Photonics
3 February 2025 in Optics Letters
Here, we have designed a novel, to the best of our knowledge, three-terminal AlGaN-based deep-ultraviolet (DUV) laser diode (LD), featuring an AlScN ferroelectric layer beneath the third terminal and a stepped ridge structure. Our findings indicate that when the AlScN layer is negatively polarized by an external bias by the third terminal, the fixed polarization positive charges at the AlScN/p-GaN interface can enhance hole injection efficiency by modulating the energy band in the p-type region near the AlScN layer. The modulation does not deteriorate the electron injection and the optical field confinement, thus effectively increasing the stimulated recombination rate in the active region. As a result, there is a marked reduction in threshold current density, accompanied by a significant rise in output light power. Furthermore, our investigation suggests that the stepped ridge structure can further mitigate the hole lateral diffusion during the hole injection process, ensuring sufficient hole current density. This study, theoretically, offers a novel way to realize high-performance AlGaN-based DUV LD.
12 January 2026 in Applied Physics Letters
The low p-doping efficiency of AlGaN due to its high activation energy limits the advancement of deep ultraviolet optoelectronics. The quantum engineering method has provided a new insight to address the challenge of acceptor activation in Al-rich AlGaN. As its unique valence band offset, the distribution of acceptor and band edge states in the barrier and well determines the acceptor activation efficiency. Here, we proposed a model for reducing the acceptor activation energy in quantum-structured p-AlGaN and provided experimental validation. By tuning the reactor pressure, we prepared periodic quantum-structured p-AlGaN with different cycles successfully. Compared to long-period quantum structures, short-period quantum structures introduce more band offsets, enhancing the wavefunction overlap between the acceptor states and the band edge states, thereby significantly promoting acceptor activation. Ultimately, we achieved an ultrathin quantum-structure p-AlGaN with an average Al content of ∼77% and a periodic thickness of 2.7 nm, reaching a record-low resistivity value of about 5.4 Ω·cm. Additionally, it is demonstrated that short-period quantum structures can facilitate hole injection in deep ultraviolet light-emitting diodes, effectively improving their external quantum efficiency. This study offers an effective p-doping strategy for Al-rich AlGaN and paves the way for applications of deep ultraviolet optoelectronics.
30 May 2024 in Optical Materials Express
AlGaN-based far-UVC LEDs are urgently in demand recently. However, as the wavelength decreases below 250 nm, the EQE experiences a significant decrease due to the increasing difficulty of realizing high-efficiency doping and high crystal quality with increasing Al content, resulting in severe carrier non-uniform distribution in the MQWs and limiting the radiative recombination. Here, we investigate the effect of the number of well-barrier pair in the MQWs on the performance of AlGaN-based far-UVC LEDs regarding carrier distribution and confinement. The results indicate that an insufficient number of well-barrier pair in the MQWs will lead to excessive carrier injection and insufficient carrier confinement, and an excessive number of well-barrier pairs will make it difficult for carriers to diffuse to the distal quantum wells. It is found that the MQWs with six pairs of well-barrier may be more suitable for far-UVC LEDs. This study provides a feasible direction to optimize far-UVC LEDs.