Se tiene por objetivo analizar la gestión de residuos sólidos desde una revisión documental. Se trabajó la metodología de investigación descriptiva. Se logró identificar el limitado conocimiento que tienen las autoridades municipales sobre gestión y el manejo de los RSD y RSND. Se necesita mejorar el proceso de la gestión de los RSD y RSND, a fin de brindar beneficios a la población en las zonas rurales y dispersas en el ámbito de los Tambos. Los Equipos Territorial MIDIS, deben acompañar y brindar asistencia técnica a los gobiernos locales para la implementación de las agendas en gestión, de los residuos sólidos, en el marco de las prioridades de la PNDIS, vinculándolas a los instrumentos de gestión de los gobiernos regionales con la finalidad de promover una adecuada gestión y manejo de residuos sólidos en el ámbito de los Tambos.
Los motores de combustión interna cumplen un papel muy importante en nuestra sociedad, ya que son fundamentales en el transporte y la industria, muchas de estas máquinas son monocilíndricos y de baja cilindrada. En este contexto, el presente estudio tiene como objetivo principal determinar el ciclo teórico Otto mediante fichas técnicas proporcionadas por el fabricante. La metodología combina parte cualitativa y cuantitativa, la primera evalúa de manera gráfica los ciclos teóricos y su comportamiento de cada uno, la segunda, analiza la eficiencia, presiones, volumen, temperatura y energía transferidas para cada ciclo Otto estimado. Los resultados demuestran que los cuatro motores tienen eficiencias térmicas similares (entre 58.5% y 60.2%), sin embargo, el motor XTZ 125 destaca con una eficiencia (60.2%), concluyendo que la relación de compresión, es esencial para determinar su eficiencia, y que, a mayor cilindrada, no necesariamente va a ser más eficiente el motor. Esto es corroborado con el valor del calor rechazado que en el motor XTZ 125 es 323.701 kJ/kg, siendo el mínimo en relación a los cuatro motores estudiados, teniendo éxito en convertir gran parte del calor cedido en trabajo.
The cutting tools used in heavy machinery are subjected to severe abrasion, impact, and cyclic loading conditions, which cause progressive material loss and reduce their service life. The objective of this research was to evaluate the structural integrity of cutting tools restored by submerged arc welding (SAW) in order to determine their feasibility for reuse. The restoration process was carried out using T-500 wear-resistant steel, 3.2 mm EL-12 welding wire, and R35Mo flux, with welding parameters of 350 A, 30 V, and a travel speed of 30 cm/min. Microstructural and chemical composition analyses were performed, together with tensile, impact, hardness, and wear tests, complemented by structural and fatigue analyses. The average tensile strength was 1014.5 MPa, with fracture occurring in the base metal, while the average absorbed impact energy was 124.13 J. The welded zone exhibited an average wear rate of 0.01040 g/min compared with 0.01400 g/min for the base metal, representing a 25.7% reduction. Fatigue analysis estimated 61,447 cycles to reach total cumulative damage. The results demonstrate the technical feasibility of the SAW process for restoring the cutting tools evaluated.
The purpose of this research was to analyse the influence of the improvement plans on the learning indicators measured in the subjects Electropneumatic Automation and Transformers and Transmission Lines taught in the professional career of Mechanical and Electrical Engineering at the National University of Jaén, Cajamarca, Peru. The improvement plans are aimed at strengthening the quality of the teaching-learning process and were implemented starting in 2020. The measurement and evaluation of learning was carried out according to the following stages: definition of the educational objectives of the programme, construction of the matrix of the contribution of the subjects in the learning indicators, selection of the subjects and elaboration and implementation of the improvement plans. The learning indicators obtained from the implementation of the improvement plans were processed following the established guidelines for an analysis of variance and Tukey's multiple comparisons test, obtaining evidence that indicates the existence of highly significant differences when comparing semesters and learning indicators with respect to the percentage of the level of achievement reached, which reflects the influence of the improvement plans that acquire a continuous character when applied semester after semester