16 December 2013 in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
A non-standard aerodynamic design idea has been proposed for the supersonic or the transonic axial flow compressors. The aim of this non-standard design idea is to further increase the stage load efficiently with boundary layer suction used only in the stator, which can reduce the design difficulty of the air bleed system in the rotating part and improve the reliability of the stage. Compared with the conventional supersonic shock-in-type rotor, the rotor designed by this method can further increase the turning of the flow to enhance the stage work. Compared with the traditional supersonic impulse rotor, it can lower the rotor exit absolute Mach number to relieve the design difficulty of the downstream stator. But by increasing the turning of the flow in the rotor, the stator entrance Mach number will be increased inevitably, so boundary layer suction is used to solve its internal flow problems. Based on the numerical simulation, a verification stage has been designed to demonstrate the feasibility of this non-standard aerodynamic idea. From the three-dimensional viscous numerical results, a stage with total pressure ratio 2.56 has been attained at tip tangential speed 370 m/s. For this aspirated stage, three kinds of efficiency evaluation methods are applied, and the corresponding stage maximum efficiency is around 91% (calculated by formula (5)), 87% (calculated by formula (6)), and 83.4% (calculated by formula (7)) separately. The total bleed mass flow rate in the stator is around 5.8% of the inlet.
15 January 2022 in Journal of Thermal Science
1 January 2015 in Heat Transfer Research
The need to design high performance of a cooled gas turbine is considered with emphasis made on coupled aerodynamic and heat transfer optimization of the vane, blade, and single stage cooled gas turbine by using a multiobjective optimization method. The aerodynamic profile is designed to have three sections and the cooling structure to consist of a serpentine passage, with a tail transverse channel and trailing edge slots. The optimization platform is built up in an in-house code using a cooling structure parametric method based on MATLAB, as well as automatic grid generation methods, a blade profile parametric program in FORTRAN, the software ISIGHT and ANSYS-CFX. The optimization platform evaluates the aerodynamic effects through the aerodynamic efficiency and presents the cooling effect by the high-temperature coefficient. The pressure drop is described by a pressure drop function. The multiobjective optimization method is accomplished by optimizing the inlet flow angle, installation angle, and the post-corner angle of the vane and blade profiles, while the position of partition is the optimized variable of the cooling structure. The results show that there exists an optimum case in aerodynamic efficiency, high-temperature coefficient, and pressure drop in a Pareto-optimal front.
4 August 2017 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
In this paper, the synergistic effect between compound lean and aspiration on the aerodynamic performance of compressor cascades is discussed. Preliminary experimental data verify the accuracy of the computational fluid dynamics method adopted, and a thorough study on reciprocal effect among lean angle, aspirated flow fraction and aspiration streamwise location is conducted. The calculations show that, due to the shorter streamwise length of the re-grown boundary layer against adverse pressure gradient, the aspiration location located farther downstream from the leading edge can minimize the loss of the blade passage flow. With the application of blade lean, which is similar to the flow control mechanism in the unaspirated cascades, an increase in pressure at the suction surface corner is used to migrate the low momentum fluid from the corners towards the midspan of the suction surface. Meanwhile, the reduced aspirated flow velocity and the improved favorable pressure gradient in the lean anterior plenum can reduce the entropy rise through the plenum. Simultaneously, the suction power required in the blade passage flow is reduced with blade lean, while the suction power for the aspirated flow through the plenum shows the opposite trend.
1 March 2014 in Catalysis Communications
25 December 2023 in IEEE Access
To optimize the performance of the soft actuator, numerical experiments and regression analysis of the multi-structure parameter are presented based on the numerical calculation method. Firstly, numerical experiments and regression analysis were performed on the parameters of different driving channel shapes, including equilateral triangle, square, regular pentagon, regular hexagon, and circle, to determine the driving performance under different channel cross-sections. Secondly, numerical experiments and regression analysis were conducted on the parameters of fiber winding diameter and winding angle of the soft actuator, and qualitative analysis was performed on the failure states of the numerical calculations. Lastly, numerical experiments and regression analysis were carried out on the parameters of wall thickness and driving channel length of the soft actuator to determine the influence of these parameters on the driving performance. Through the numerical experiments and regression analysis, this study provides a necessary theoretical foundation for the optimization design of soft actuator, effectively improving the development efficiency and dynamic performance of soft actuators.