Anastasiya B. Speshilova

Anastasiya B. Speshilova

Auto-generated profile, based on publicly available information

Anastasiya B. Speshilova

Peter the Great St. Petersburg Polytechnic University 1 , St. Petersburg 195251, Russian Federation

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 December 2020 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
AOArmenak A. Osipov
Armenak A. Osipov
GIGleb A. Iankevich
Gleb A. Iankevich
ASAnastasiya B. Speshilova
Anastasiya B. Speshilova
ASAlexander Shakhmin
Alexander Shakhmin
VBVladimir I. Berezenko
Vladimir I. Berezenko
SASergey E. Alexandrov
Sergey E. Alexandrov
This work is an extensive study of the plasma chemical etching (PCE) process of single-crystalline lithium niobate (LiNbO₃) in the SF₆/O₂ based inductively coupled plasma (ICP). The influence of the main technological parameters of the LiNbO₃ PCE process, including the distance between the sample and the lower edge of the discharge chamber, as well as the temperature of the substrate holder on the etching process rate, has been studied. It was shown that changing the temperature of the substrate holder in the range from 100 to 200°C, leads to a gradual rise of the etching rate from 127 to 282 nm/min. A further increase in the temperature to 250°C, results in a sharp increase in the etching rate to 711 nm/min. The maximum achieved etching rate in experimental series which were aimed at determining the dependence of the LiNbO₃ etching rate on the temperature of the substrate holder was 812 nm/min at a substrate holder temperature of 325°C. With the help of X-ray photoelectron spectroscopy (XPS) technique was found and shown that during the etching process in fluorinated plasma the nonvolatile LiF compound is formed on the surface of the treated LiNbO₃. On the basis of the obtained results, the optimal process of deep ( > 80 μm) LiNbO₃ PCE was developed, with an etched wall inclination angle of ≈ 110°, with selectivity ratio to Cr mask of ≈ 20, and an etching rate of about 300 nm/min. [2020-0317]

20 April 2023 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Open access
PDF file
AGAlina Gagaeva
Alina Gagaeva
ASAnastasia Speshilova
Anastasia Speshilova
AOArmenak Osipov
Armenak Osipov
YEYakov Enns
Yakov Enns
AKAlexey Kazakin
Alexey Kazakin
SASergey Alexandrov
Sergey Alexandrov
In this work, we studied the influence of technological parameters of plasma chemical etching of silicon on silicon etching rate, photoresist etching rate, etching selectivity of silicon in relation to a photoresist, and sidewall angle of etched structures. It was found that the silicon etching rate increases with raising percentage of SF6 in the gas mixture (25%–50%), pressure (1–2.5 Pa), high-frequency (HF) power (1000–2000 W), and bias voltage module (15–75 V) and decreases with a raising total flow rate of the gas mixture (5–35 SCCM) due to the increasing passivation efficiency of the sample surface. The etching selectivity increases with a raising percentage of SF6 and pressure and decreases with the raising total gas flow rate, HF power, and bias voltage module due to different influences of technological parameters on the photoresist etching rate. In addition, based on the obtained results, a common regularity between the sidewall angle and the optical emission spectra was revealed. The method of in situ diagnostics was proposed, namely, controlling the sidewall angle by a ratio of emission intensities of a carbon line (517.1 nm) to a fluorine line (685.8 and 703.9 nm) designated as parameter X. It was found that the sidewall angle of etched structures takes certain values depending on the value of the X parameter. The ranges of X values at which the sidewall angle is acute, right, and obtuse were estimated. So, at values of X from ≈0.15 to ≈0.35, an acute angle (from 81° ± 0.5° to 89° ± 0.5°) is obtained; at X from ≈0.35 to ≈0.42, a right angle is obtained (90° ± 0.5°); and at X from ≈0.42 to ≈0.75, the values of the sidewall angle are in the range from 91° ± 0.5° to 94° ± 0.5°, no matter which technological parameters were set. Experiments were conducted for etching windows with linear dimensions from 0.5 × 20 to 2 × 20 mm.

28 September 2023 in Plasma Processes and Polymers
Verified
Journal Article
Closed access
ABAnastasia S. Bil
Anastasia S. Bil
SASergei E. Alexandrov
Sergei E. Alexandrov
ABAlexander D. Breki
Alexander D. Breki
ASAlexander L. Shakhmin
Alexander L. Shakhmin
ASAnastasia B. Speshilova
Anastasia B. Speshilova

26 December 2023 in Cellulose
Verified
Journal Article
Closed access
PDF file
EEE. V. Endiiarova
E. V. Endiiarova
AOArtem Osipov
Artem Osipov
ASA. L. Shakhmin
A. L. Shakhmin
ASA. B. Speshilova
A. B. Speshilova
AKAlmaz Kamalov
Almaz Kamalov
SAS. E. Alexandrov
S. E. Alexandrov

19 September 2024 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
PDF file
AFAlina E. Fumina
Alina E. Fumina
ASAnastasia B. Speshilova
Anastasia B. Speshilova
EEEkaterina V. Endiiarova
Ekaterina V. Endiiarova
AOArmenak A. Osipov
Armenak A. Osipov
SASergey E. Alexandrov
Sergey E. Alexandrov
In this work, a method for in situ diagnostics of the etching profile of silicon structures (etching window sizes 15–400 μm) using optical emission spectroscopy was proposed. To determine the relationship between the etching profile and plasma parameters, the influence of technological parameters on the etching characteristics (vertical and lateral etching rate, selectivity in relation to photoresist, and sidewall angle) was studied. As a general parameter, which reflects the changes in plasma characteristics depending on the selected technological parameters, the parameter X (C/F ratio in SF6/C4F8 plasma) was introduced. Based on the results obtained, a general pattern between the lateral etching rate, sidewall angle, and optical emission spectra was identified. Thus, ranges of X values, at which the lateral etching rate does not exceed 5 nm/min for 15–30 μm structures and 15 nm/min for 100 μm structures, were estimated: 0.38 ≤ X ≤ 0.77 and 0.28 ≤ X ≤ 0.46, respectively. For 250–400 μm structures, ranges of X values, at which the sidewall angle is acute, straight, and obtuse, were determined: 0.16 ≤ X < 0.29, 0.29 ≤ X ≤ 0.41, 0.41 < X ≤ 0.75, respectively.

20 October 2022
Verified
Conference Paper
Closed access
YEYakov Enns
Yakov Enns
VSVitaly Studzinsky
Vitaly Studzinsky
AUAleksandr Uvarov
Aleksandr Uvarov
ENEkaterina Nikitina
Ekaterina Nikitina
ASAnastasia Speshilova
Anastasia Speshilova
PKPlaton Karaseov
Platon Karaseov
This paper presents the results of investigation of gold nanoparticle array formation on GaN surface and its plasmon effect. Gold nanoparticles are formed on GaN layer grown by molecular beam epitaxy (MBE) by solid-state dewetting technique both in the air at atmospheric pressure and under vacuum conditions. The influence of the thickness of as-deposited gold film and annealing ambient on the size and spatial distribution of nanoparticles was studied. Investigation of optical characteristics showed the appearance of the surface plasmon resonance effect. The results reveal the possibility to increase the efficiency of GaN-based optoelectronic devices by Au nanoparticle arrays.