1 May 2020 in IOP Conference Series: Earth and Environmental Science
Two small-scale reinforced concrete beams, one made of ordinary Portland cement (NC) and the other blended with supplementary material using fly ash (SMFA), were investigated to gain insights into their flexural behaviour. Class F fly ash by 15 per cent of the mass of cement was added in the concrete mix of SMFA beam, enabling the reduction of cement usage. The specimens were designed under-reinforced having low steel bar ratio and were tested under four-point bending to failure. To ensure the beam failing in flexure, the M/Vd ratio of 3.2 was customary to allow the development of flexural cracks transpired over the centre span as the load further increased. Predictions incorporating manual calculation and computer simulation using Response-2000 were also performed and compared against the experimental data. The results showed that the NC and SMFA beams were generally equivalent in terms of load-deflection response, crack pattern, and mode of failure. Nonetheless, it should be marked that the load-carrying capacity of the SMFA beam was 22 per cent higher than that of NC beam, while the deflection of the SMFA beam was found to be significantly higher. Predictions from the manual calculation and computer simulation using Response-2000 were also in good agreement with the results obtained from the experiment.
31 March 2018 in International Journal on Advanced Science, Engineering and Information Technology
Assessment of Vulnerable Buildings Due to Earthquake Loading Using Rapid Visual Screening Smartphone Application
1 May 2020 in IOP Conference Series: Earth and Environmental Science
A series of small-scale rectangular reinforced concrete beams made with different mix proportions were presented. The beams were fabricated using normal concrete designated as specimen control (NC), normal concrete blended with supplementary material using Class F fly ash (SMFA), and engineered cementitious composite (ECC). The beams comprised of similar reinforcement where the ratio of compression, tension, and transverse bars were 1.0%, 1.5%, and 1.0% respectively. To this end, the beams were tested under four-point bending and they were intended to fail in flexure mode. The tests also aimed to provide direct evidence regarding the improvement of beam ductility due to the use of ECC. Furthermore, the performance of test beams on the overall strength, crack pattern, and damage state was also assessed. To corroborate the experimental work, an analytical work employing nonlinear finite element analysis using Abaqus was also included. From this study, it was found that each beam demonstrated a discernible ductile plateau upon the post-cracking region with Beam ECC showing the largest ductility compared to the other two thereby suggesting that the use of ECC could enhance the beam ductility. It was also shown that the flexural cracks manifested in Beam ECC were less critical, signifying that ECC is a damage-tolerant composite. Furthermore, the overall results of predicted load-deflection and damage state obtained from Abaqus were also in a good agreement with the experimental results.
1 May 2020 in IOP Conference Series: Earth and Environmental Science
Results of an experimental investigation on shear-critical responses of small-scale reinforced concrete beams fabricated with normal concrete (NC) and concrete blended with supplementary materials using Class F fly ash (SMFA) are presented. The beams were reinforced with adequate stirrups as per requirement specified in design specifications. The beams were tested using Ohno beam testing setup to induce direct shear mechanisms across the shear plane. It was also intended to evaluate the shear capacity of a disturbed region (D-region) where the flexural moment was negligible. It was found that all beams fail in brittle shear manner, showing a significant increase of shear forces with a subtle increase in beam deflection. It was also found that the use of adequate stirrups could cease the localised crack formation. In overall results, it was found that the use of Class F fly ash as cement replacement was applicable because the response did not differ significantly.
30 December 2017 in MATEC Web of Conferences
Uniform corrosion still widely used by a lot of researchers and engineers to analyze the corrosion induced cracking. However, in practice, corrosion process occurred non-uniformly. The part nearest to the exposed surface is more likely to have faster corrosion initiation compared with other regions. This research is mainly focused on investigating the effect of non-uniform rust distribution to cover cracking in reinforced concrete. An experimental test performed using accelerated corrosion test by using 5% NaCl solution and applied a constant electric current to the concrete samples. The rust distribution and measurement were observed by using a digital microscope. Based on the experimental result, it was found that the rust was distributed in a non-uniform pattern. As a result, the cracks also formed non-uniformly along the perimeter of steel bar. At the last part of this paper, a simulation result of concrete cracking induced by non-uniform corrosion is presented. The result compared with a simulation using uniform corrosion assumption to investigate the damage pattern of each model. The simulation result reveals stress evolution due to rust expansion which leads to concrete cracking. Furthermore, a comparison of stresses induced by non-uniform corrosion and uniform corrosion indicates that non-uniform corrosion could lead to earlier damage to the structure which is specified by the formation and propagation of the crack.
1 August 2025 in Civil Engineering Journal
This study investigates the shear behavior of reinforced concrete beams constructed with high-calcium fly ash-based Ultra-Low Carbon Concrete (ULCC) as a sustainable alternative to conventional Portland Cement Concrete (PCC). The objective is to assess ULCC’s structural performance under shear and its potential as a low-carbon substitute. Using a dry-mix method with dry activators, six beams (five ULCC, one PCC) of identical dimensions (150 × 250 × 1800 mm) were tested under four-point bending, with variations in shear reinforcement, flexural reinforcement, and shear span-to-depth (a/d) ratios. Digital Image Correlation (DIC) was employed to monitor crack propagation and strain development, while Finite Element Modeling (FEM) provided numerical validation. Results show that increasing shear reinforcement enhanced capacity by 12.05%, whereas higher (a/d) ratios decreased it by 22.63%; increased flexural reinforcement improved shear resistance by 31.27%. FEM closely matched experimental outcomes, with a load-deflection ratio of 1.01. ULCC outperformed PCC in shear capacity and exceeded ACI 318-19 predictions. The integration of DIC and FEM offers a comprehensive analysis framework, and the findings demonstrate ULCC’s viability as a structurally efficient, environmentally sustainable alternative for shear-critical applications.