1 January 2018 in Shock and Vibration
Based on the Lagrange equation in system dynamics, aiming at the horizontal cutting process, the dynamical coupling model of boom‐type roadheader’s body pose was established. According to input problem of solving the model, a calculation method of the cutting head load was proposed, and the relationship between the cutting head load and pressure of the driving cylinders and swing angle of the cutting arm was obtained through simulating analysis. The simulation model was established to solve the dynamical coupling model. The cutting head load, horizontal swing angle of the cutting arm, and dip angle of coal seam were regarded as independent variables to perform changing parameter analysis in variations of the body pose. The field experiment was carried out, and the measured data is basically consistent with the simulation values. The results show that lateral displacement of the body can reach up to 6.5 cm, backward displacement can reach up to 5.2 cm, floor‐based quantity can reach up to 11 cm, pitch angle of the body can reach up to 7.8°, and roll angle can reach up to 2.1°. Variations of the body pose parameters are influenced greatly by the cutting head load, while the influence from horizontal swing angle of the cutting arm and dip angle of coal seam is slighter. Among the pose parameters, floor‐based quantity and pitch angle of the body vary relatively greatly, which tend to seriously influence forming quality of the roadway and should be mainly considered in deviation rectification of the roadheader’s body pose.
1 January 2018 in Shock and Vibration
The intense vibration of a roadheader rotary table damages the cutting system of the roadheader and reduces the efficiency. This paper analyzes the vibration of a rotary table by combining the finite element model with tested data from an underground coalmine. First, the force of the rotary table during the cutting procedure was analyzed, and the finite element model was built using Pro/E and ADAMS. The tested data were then imported into the model after selection, procession, and combination were conducted. Next, the six lowest‐order parameters of the rotary table were calculated. A vibration analysis of the rotary table under certain working conditions was conducted, and the results were compared with those from a modal experiment using a single‐point excitation method. According to the comparison between the simulation result and experiments, it is clear that this method is both reasonable and feasible. And it could supplement the theoretical foundation of the analysis of other roadheader components, providing reference for the improvement of the structure and dynamic properties of a roadheader. In addition, other vibration components of a roadheader such as the cutting head and the cutting arm could also be analyzed through the proposed method, with very reliable precision.
23 October 2018 in Journal of Mechanical Science and Technology
25 February 2021 in IEEE Transactions on Plasma Science
Previous researches show that grading capacitors truly improve the dynamic voltage distribution uniformity of multibreak vacuum circuit breakers (VCBs). However, large capacitors can reduce the breaking capacity. In order to obtain balanced voltage distribution with small capacitors, nonsynchronous external magnetic field was adopted. The Helmholtz coil was designed to generate a stable magnetic, and nonsynchronous magnetic field control system was designed to realize double-break nonsynchronous control. The 3-D models of Helmholtz coil and axial magnetic field (AMF) contact were simulated and analyzed in Maxwell. The external magnetic field (EMF) experiment platform for double-break vacuum gaps was set up. In the experiment, the strength of EMF on each break can be adjusted by the nonsynchronous magnetic field control system. The experimental results show that different EMF strengths on two vacuum breaks in series can improve the voltage distribution uniformity. Meanwhile, the magnetic field strength has the best matching parameters. The works in this article provide references for magnetic field regulation and interruption performance of VCBs.
1 January 2019 in Mathematical Problems in Engineering
Trajectory planning and tracking control algorithm based on a position and orientation deviation model are proposed to achieve path correction for the mining boom road‐header working underground. The proposed strategy is assessed to be feasible and potentially practicable by simulations, from which the following statements are summarized. Firstly, trajectory planning is necessary since different trajectories correspond to different scenarios about undesirable excavation space, slipping level, and power consumption. Secondly, using the proposed tracking control algorithm, the road‐header is guided back onto the expected path in limited adjusting steps, with smoothly varying rotation speeds of the driving wheels and regularly reducing pose errors. Lastly, it shows that by implying the SVD‐unscented Kalman filtering in the tracking control, the adverse impacts of process and measurement noises are appeased obviously. This research provides an advisable modeling and valuable simulation for the road‐header to achieve robotic operation underground.