Luciana Montanari

Luciana Montanari

Auto-generated profile, based on publicly available information

Luciana Montanari

Escola de Engenharia de São Carlos, University of São Paulo, São Carlos, Brazil

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2014 in Prosthetics and Orthotics International
Verified
Journal Article
Open access
PDF file
RARogério Araújo
Rogério Araújo
PTPedro Teixeira
Pedro Teixeira
LMLuciana Montanari
Luciana Montanari
Ana Rosanete ReisAna Rosanete Reis
Ana Rosanete Reis
Maria Beatriz SilvaMaria Beatriz Silva
Maria Beatriz Silva
Paulo MartinsPaulo Martins
Paulo Martins
The investigation draws from the fundamentals of the mechanical behaviour of titanium grade 2 to the design and fabrication of facial implants by means of single point incremental forming. To provide knowledge on the capabilities and limitations of a new manufacturing technology to fabricate low-cost, patient-specific medical implants. Rapid fabrication of a simplified model of a facial implant. Circle grid analysis and its graphical representation in the fracture forming limit diagram combined with finite element modelling are utilized to identify the failure limits and to assist the overall design of the facial implants. Fabrication of facial implants without and with failure by cracking due to excessive thinning of the sheet from where the implant is to be cut. Identification of the major operative parameters that influence fabrication of sound facial implants by means of single point incremental forming. Reduce the gap between production engineers and the medical community by presenting a state-of-the-art manufacturing technology to produce low-cost, patient-specific medical implants.

1 June 2014 in International Journal of Mechanical Sciences
Verified
Journal Article
Closed access
VCV.A. Cristino
V.A. Cristino
LML. Montanari
L. Montanari
Maria Beatriz SilvaMaria Beatriz Silva
Maria Beatriz Silva
AAA.G. Atkins
A.G. Atkins
Paulo MartinsPaulo Martins
Paulo Martins

1 September 2008 in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Verified
Journal Article
Closed access
RJR G Jasinevicius
R G Jasinevicius
JDJ G Duduch
J G Duduch
LML Montanari
L Montanari
PPP S Pizani
P S Pizani
Single-point diamond turning of monocrystalline semiconductors is an important field of research within brittle materials machining. Monocrystalline silicon samples with a (100) orientation have been diamond turned under different cutting conditions (feed rate and depth of cut). Micro-Raman spectroscopy and atomic force microscopy have been used to assess structural alterations and surface finish of the samples diamond turned under ductile and brittle modes. It was found that silicon undergoes a phase transformation when machined in the ductile mode. This phase transformation is evidenced by the creation of an amorphous surface layer after machining which has been probed by Raman scattering. Compressive residual stresses are estimated for the machined surface and it is observed that they decrease with an increase in the feed rate and depth of cut. This behaviour has been attributed to the formation of subsurface cracks when the feed rate is higher than or equal to 2.5 μm/rev. The surface roughness was observed to vary with the feed rate and the depth of cut. An increase in the surface roughness was influenced by microcrack formation when the feed rate reached 5.0 μm/rev. Furthermore, a high-pressure phase transformation induced by the tool/material interaction and responsible for the ductile response of this typical brittle material is discussed based upon the presented Raman spectra. The application of this machining technology finds use for a wide range of high quality components, for example the creation of a micrometre-range channel for microfluidic devices as well as microlenses used in the infrared spectrum range.

13 June 2013 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
LML. Montanari
L. Montanari
VCV. A. Cristino
V. A. Cristino
Maria Beatriz SilvaMaria Beatriz Silva
Maria Beatriz Silva
Paulo MartinsPaulo Martins
Paulo Martins

12 October 2011 in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Verified
Journal Article
Closed access
RJRenato Goulart Jasinevicius
Renato Goulart Jasinevicius
JDJ G Duduch
J G Duduch
LML Montanari
L Montanari
PPP S Pizani
P S Pizani
The objective of this paper is to show the dependence relationship between the crystallographic orientations upon brittle-to-ductile transition during diamond turning of monocrystalline silicon. Cutting tests were performed using a −5° rake angle round nose diamond tool at different machining scales. At the micrometre level, the feedrate was kept constant at 2.5micrometres per revolution (µm/r), and the depth of cut was varied from 1 to 5 µm. At the submicrometre level, the depth of cut was kept constant at 500 nm and the feedrate varied from 5 to 10 µm/r. At the micrometre level, the uncut shoulder generated with an interrupted cutting test procedure provided a quantitative measurement of the ductile-to-brittle transition. Results show that the critical chip thickness in silicon for ductile material removal reaches a maximum of 285 nm in the [100] direction and a minimum of 115 nm in the [110] direction, when the depth of cut was 5 µm. It was found that when a submicrometre depth of cut was applied, microcracks were revealed in the [110] direction, which is the softer direction in silicon. Micro Raman spectroscopy was used to estimate surface residual stress after machining. Compressive residual stress in the range 142 MPa and smooth damage free surface finish was probed in the [100] direction for a depth of cut of 5 µm, whereas residual stresses in the range 350 MPa and brittle damage was probed in the [110] direction for a depth of cut of 500 nm.

6 December 2013 in Materials Research
Verified
Journal Article
Open access
PDF file
JGJuno Gallego
Juno Gallego
Alessandro Roger RodriguesAlessandro Roger Rodrigues
Alessandro Roger Rodrigues
CACleiton Lazaro Fazolo Assis
Cleiton Lazaro Fazolo Assis
LMLuciana Montanari
Luciana Montanari
Grain size refinement is one of the most efficient strengthening mechanisms applied to modern High-Strength Low-Alloy steels (HSLA) because yield strength and toughness are both improved. This paper discusses the distribution of carbides by using transmission electron microscopy (TEM) in a low-carbon steel with ultrafine grained (UFG) ferrite. Fine cementite particles were formed during water quenching due to the auto-tempering of highly distorted martensite. Other fine particles observed under the same condition were nucleated due to the presence of carbide formers such as niobium, titanium and vanadium. TEM analysis showed that cementite particles underwent Ostwald ripening during warm rolling but they were still able to inhibit ferrite grain growth, which was maintained 1µm size approximately.