Ozkan Sengul

Ozkan Sengul

Auto-generated profile, based on publicly available information

Ozkan Sengul

Faculty of Civil Engineering, Istanbul Technical University, Istanbul 34469, Turkey

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2009 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
OSOzkan Sengul
Ozkan Sengul
MTMehmet Ali Tasdemir
Mehmet Ali Tasdemir
Concretes with binary and ternary blends of portland cement, finely ground fly ash and finely ground granulated blast furnace slag were produced to investigate their effects on compressive strength and rapid chloride permeability. Portland cement was partially replaced by finely ground fly ash (Blaine specific surface: 604 m2 /kg ) and finely ground granulated blast furnace slag (Blaine specific surface: 600 m2 /kg ). Two series of concrete with water/binder ratios of 0.60 and 0.38 were produced and for both water/binder ratios, portland cement was replaced by: (i) 50% fly ash; (ii) 50% blast furnace slag; and (iii) 25% fly ash+25% blast furnace slag. At the high water/binder ratio, compressive strengths of the concretes with the pozzolans are lower compared to that of the portland cement concrete. At the low water/binder ratio, however, these strength reductions are less compared to the high water/binder ratio and compressive strength of the concrete produced with 50% slag was even higher than the port...

24 October 2015 in Arabian Journal for Science and Engineering
Verified
Journal Article
Closed access
PDF file
CECaner Elibol
Caner Elibol
OSOzkan Sengul
Ozkan Sengul

2 August 2020 in Journal of Material Cycles and Waste Management
Verified
Journal Article
Closed access
PDF file
FSFatih Salihpasaoglu
Fatih Salihpasaoglu
OSOzkan Sengul
Ozkan Sengul

17 December 2024 in International Journal of Concrete Structures and Materials
Verified
Journal Article
Open access
PDF file
SGSaadet Gokce Gok
Saadet Gokce Gok
OSOzkan Sengul
Ozkan Sengul
This paper presents the outcomes of a study in which continuous steel fibers, recovered from scrap tires of vehicles, were used to prepare alkali-activated slag-based slurry infiltrated fibrous concrete (SIFCON). In this experimental study, the steel fibers used were 250 mm long, with varying fiber contents of 0%, 1%, 2%, 3%, 4%, and 5%. The alkali-activated SIFCONs were produced by activating ground granulated blast furnace slag (GGBS) with a mixture of sodium hydroxide (NaOH) and sodium silicate (Na2SiO3) solutions. Mixtures with ordinary Portland cement (OPC) were also cast for comparison purposes. The feasibility of utilizing finely ground waste glass as a silicate source for chemical activator solution in alkali-activated SIFCONs was also investigated. In this context, two different molar concentrations of NaOH, namely 8 M and 14 M, were employed during production. As activators, one series of mixtures utilized sodium hydroxide and sodium silicate solutions, while the other series replaced sodium silicate with finely ground waste glass. As a result, three different waste materials were utilized in concrete. 30 different mixtures were cast and examined in the experimental study. Load–deflection curves were obtained in three-point bending test and mechanical properties of the mixtures such as compressive, splitting and flexural strengths, fracture energy, and toughness were determined. The flexural strength and toughness increased with the use of waste steel fibers. The continuous waste fibers derived from discarded tires yielded results comparable to commercially available fibers, demonstrating their effectiveness in enhancing mechanical properties. Depending on mix design, the alkali-activated SIFCON attained flexural strength exceeding 75 MPa and compressive strength surpassing 100 MPa. These results suggest that concretes incorporating a variety of waste materials can be effectively combined. This innovative approach bridges an existing gap in the literature by combining alkali activation, waste glass, and waste steel fibers, ultimately yielding a sustainable composite that outperforms normal concretes in terms of mechanical properties while promoting environmental sustainability. Test results demonstrate that it is possible to obtain concrete with comparable mechanical properties while primarily composed of by-products and waste materials. This approach marks a substantial step in achieving high-performance concrete that relies solely on waste or by-products. Graphical Abstract


1 December 2025 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
CCCansu Colak
Cansu Colak
OSOzkan Sengul
Ozkan Sengul
This study introduces a decision-oriented framework integrating fresh-state rheology, standardized post-cracking performance, and cradle-to-gate embodied carbon for steel-fiber-reinforced concretes incorporating recycled and commercial fibers. The motivation lies in achieving mechanical efficiency while reducing the environmental burden of cementitious composites. Mixtures were produced with water-to-binder ratios between 0.40 and 0.60, fiber dosages of 15–45 kg/m3, and 50% GGBS replacement to mitigate binder-related carbon emissions. Equal-workability comparisons were conducted at 15 kg/m3 using ICAR-based static yield stress measurements, whereas higher dosages were evaluated without rheology-based adjustment. Post-cracking performance was assessed through residual flexural strengths at CMOD = 0.5 and 2.5 mm (fR1, fR3) and CMOD-based toughness indices. Embodied performance was quantified using the embodied-carbon-per-performance (ECP) index, normalized by fR3. Results indicate that recycled fibers exhibit greater fresh-state resistance but slightly lower residual capacities under equal workability, while commercial fibers achieve competitive ECP at 15 kg/m3. Increasing fiber dosage improved toughness yet intensified the trade-off between ECP and mechanical gain. The framework highlights that optimized binder composition and fiber type selection can yield carbon-efficient, structurally resilient composite systems.