Iryna Rudnieva

Iryna Rudnieva

Auto-generated profile, based on publicly available information

Iryna Rudnieva

Kyiv National University of Construction and Architecture

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 May 2022 in Strength of Materials and Theory of Structures
Verified
Journal Article
Open access
PDF file
HTHennadii Tonkacheiev
Hennadii Tonkacheiev
OMOleksandr Molodid
Oleksandr Molodid
OGOleksandr Galinskyi
Oleksandr Galinskyi
RPRuslana Plokhuta
Ruslana Plokhuta
IRIryna Rudnieva
Iryna Rudnieva
YPYurii Priadko
Yurii Priadko
Introduction. During the inspection of buildings and structures and development of design documentation for restoration works it was found that there is a need to provide recommendations or to develop solutions for repair work. These repair works either are not regulated by standards or may be technically or economically inefficient. Problem Statement. The most common defect of the tension zone in reinforced concrete beams, floor slabs or roof slabs are cracks. Injection technology is normally used to repair it. However, in case of large number of small cracks, this technology is time consuming. Purpose. Development of a new technology for repairing the tension zone of reinforced concrete beams, floor slabs or roof slabs with a large number of small cracks. This will ensure maximum filling of cracks with polymer compositions with their subsequent bonding. Materials and methods. A number of factors that may affect the technology of filling cracks with polymer compositions have been identified from the analysis of scientific and technical literature. A special device ‘tray’ was produced for experimental research. It was attached to the lower zone by a system of ties or props. A repair mix to fill the cracks was fed into the tray under pressure. By means of changing the experiment conditions the strengthening level of previously destroyed samples were set. Results. As a result, it was found that the maximum filling of cracks with the polymer composition is achieved within the 5-10 minutes of repair mix supply at a pressure in the system in the range of 0.5-0.6 atmospheres (atm). The maximum strengthening of the repaired structures under the re-applied destructive force was achieved at the conditions of repair work with a structural temperature of 20 ± 2 оС and dry state of the structure. Conclusions. The technology of repair with polymer compositions of the cracks located on the lower surface of horizontal reinforced concrete structures has been developed. It was established that in the presence of small cracks on the structure (the width is up to 0.2 mm) the developed technology is most effective, in case of widths from 0.3 to 0.8 mm it is advisable to use injection technology whereas for widths larger than 0.8 mm the hybrid technology should be applied.

24 May 2021 in Urban development and spatial planning
Verified
Journal Article
Open access
PDF file
IRIryna Rudnіeva
Iryna Rudnіeva
IGIvanna Glon
Ivanna Glon
TGTamara Grabovskaya
Tamara Grabovskaya
KPKaterina Puzina
Katerina Puzina
ІРІрина Руднєва
Ірина Руднєва
ІГІванна Глонь
Іванна Глонь
Conservation and restoration of architectural, historical and cultural heritage is of great importance for the development of cities, regions and the country as a whole. An illustrative example of this is the approach and experience of European countries. These countries have a rich and world-famous architectural, cultural and historical heritage, a high level of education, high living standards, environmental friendliness and high technology, and has become the main competitive advantage in the world. The modern idea of reconstruction, restoration and protection of monuments is not limited to attention to outstanding architectural monuments, as well as the historical and cultural heritage of the urban environment. An architectural monument is a work of historical, scientific, artistic and cultural value that has retained sufficient completeness of architectural forms for protection or restoration. The main purpose of the restoration of the monument is to preserve its historical authenticity. Through the reconstruction and restoration of monuments, the country attracts investors and develops tourism. Thus, the preservation and restoration of monuments can play a significant role in shaping modern society, as described by famous thinkers and writers. Cultural and architectural heritage sites are important assets that can be profita-ble and significantly affect the economic development of cities. Monuments of archi-tecture, culture and history are important to preserve not only because of their uniqueness, but also because they have historical and economic value for the state. The article analyzes the need to preserve the architectural heritage, considers examples of already restored buildings in Ukraine, and presents an architectural object that should be restored.

30 November 2020 in Strength of Materials and Theory of Structures
Verified
Journal Article
Open access
PDF file
IRIryna Rudnieva
Iryna Rudnieva
Built mostly centuries ago, heritage buildings as well the more contemporary buildings of the last century, which have lost the bearing capacity often need restoration and strengthening, especially in seismic regions and in regions with shrinkage phenomena (subsidence region). The need of strengthening of the building constructions during exploitation appears mostly because of their premature wear as a result of technological influences and weathering, various damage and various other factors. Traditional methods of strengthening are effective, but in some cases not appropriate or not applicable for use. An example is the increase of the load-bearing structures of historical buildings, preserving the external appearance of which is the determining factor. In this case, the use of the discussed alternative methods can be justified alternative. Knowledge of the causes of defects and damage of structures allows to choose the best option of repairing or strengthening. The aim of the research is the evaluation of the structural performance of composite fibre-reinforced elements in the wider sector of the conservation of historical, architectonic and environmental heritage, as well the more contemporary buildings of the last century, which have lost of the bearing capacity focusing reliability indexes and the appearance of the structure. In the article was described and analyzed the existing traditional methods and the alternative methods of strengthening by FRP-materials (composite materials) such building structures as masonry, metal structures, reinforced concrete, and the computation in software ABAQUS. These procedures of strengthening building structures by FRP-materials in Ukraine are not widely used due to the lack of a regulatory framework that would regulate their use, as well because these materials are relatively expensive compared to the traditional ones. The article analyzed the existing methods of computation and design of the strengthening using FRP-materials, and the computation in software ABAQUS was performed with conclusions and recommendations based on results of the computation. The aim of the work was to review the technology and analyze the advantages and disadvantages of each of the strengthen methods that should be used when choosing effective solutions for strengthening building structures. In conclusion, the need for further study and researches was confirmed.

26 June 2023 in Strength of Materials and Theory of Structures
Verified
Journal Article
Open access
PDF file
HTHennadiy Tonkacheiev
Hennadiy Tonkacheiev
VRVolodymyr Rashkivskyi
Volodymyr Rashkivskyi
IRIryna Rudnieva
Iryna Rudnieva
IDIryna Dubovyk
Iryna Dubovyk
The article considers an approach to determining the labor-intensiveness and duration of consolidation processes during the installation of structural blocks of the covering, which is caused by atypical structural and technological solutions. The relevance of this work is the need for a qualitative analysis of methods for calculating the labor intensity and duration of technological processes when justifying and making decisions regarding the organization and mechanization of assembly processes. Modern technologies of installation of structural blocks of coatings are analyzed. The analysis of labor costs was carried out for the option of using load-lifting assembly modules to reduce the specific share of the use of heavy crane equipment at the construction site. In comparison, the method of installing a structural coating using heavy crane equipment and load-lifting assembly modules is considered. To ensure the principle of comparison of options, the processes of column installation, stand installation, block consolidation, block installation, and installation and movement of a crane or assembly lifting and gathering modules are included in the consideration. All calculations were performed in tabular form according to the formula of the integer normalization method. Based on the results of the study, all the components of the labor intensity and duration of the processes were determined, on the basis of which the schedules of the consolidation and installation of the SBP blocks were built.

29 October 2021 in Strength of Materials and Theory of Structures
Verified
Journal Article
Open access
PDF file
IRIryna Rudnieva
Iryna Rudnieva
YPYurii Priadko
Yurii Priadko
HTHennadii Tonkacheiev
Hennadii Tonkacheiev
MPMykola Priadko
Mykola Priadko
The building patrimony of Ukraine includes various examples of metallic structures, especially applied for industrial purposes and in large-span structures. The use of metal structures in construction is due primarily to their mechanical properties. They are frost-resistant and able to withstand temperatures down to -65 degrees as well as they are hard, durable, strong and reliable. They can also be used in areas with high seismic activity. However, as in the case of other types of structures, there is a need to restore or strengthen metal structures due to structural defects, wear of load-bearing elements, as well as to increase the load-bearing capacity. In several situations, strengthening with Fiber Reinforced Polymer composites (FRP) gives better results. The current article deals specifically with this strengthening technique. The main cultural reason to restore the old metallic structures and provide a structural functionality, is based on the need to preserve not only their historical origins but also the scenery value of the places in which they are located. That is why the strengthening should be carried out with the aim of maintaining the original design idea. Due to the long-term operation without timely maintenance and major repair, unique and metal large-span structures require strengthening of the load-bearing structures. It is especially important to choose the most efficient method, both in terms of reliability and cost effectiveness. This can lead to the long term interruption of the structure operation and production process, or the inability to use the adjacent territory due to the reconstruction work. At the same time, it is necessary to preserve not only the structure as a whole, but also the external architectural appearance. Traditional methods of strengthening are effective, but in some cases not effective or not applicable for use. An example is the increase of the load-bearing structures of the buildings, preserving the external appearance of which is the determining factor. In this case, the use of the discussed methods can be justified alternative. Disadvantages of steel panels and rods for strengthening are possible corrosion, considerable weight, need for high labor content of the work, and consequently the high cost of labor required to perform the work that need large area. Nowadays, one of the most dynamic types of large-span structures in architectural and structural view are suspension roofs. The aim of the research is the evaluation of the bearing capacity of the suspended rigid threads strengthened with CFRP (carbon fiber reinforced polymer) laminates and provision the general recommendations to implement reconstruction and strengthening with this type of material. Therefore it was considered variant of strengthening suspended bending-rigid fibers by composite materials. Computations are performed in software ABAQUS, as a result of which the percentage reduction in vertical deformation was 26.6% for bending-rigid fibers strengthened with CFRP laminates. The value of tensile stresses reduced by about 14 %. The obtained results of the study confirm the need for further studies and research.

1 October 2021 in Dorogi i Mosti
Verified
Journal Article
Closed access
IRIryna Rudnieva
Iryna Rudnieva
OMOleksandr Molodid
Oleksandr Molodid
SBSergey Bogdan
Sergey Bogdan
KUKyiv Llc Mapei Ukraine
Kyiv Llc Mapei Ukraine
Introduction. Reinforcement methods, which are mainly used in domestic practice to strengthen metal structures, based on adding an additional section to metal elements by bolting or welding them. These methods, of course, are reliable and effective, but they cannot always be applied when it is necessary to preserve not only the building as a whole, but also its original internal and external appearance. Moreover, metal elements increase the stress on the structure and the building as a whole and are susceptible to corrosion and fatigue. There are often cases when it is difficult to fix a reinforcement element to the main structure, both from a technological and constructive point of view. In these situations, it becomes necessary to reinforce metal structures with high-strength materials with low weight and high manufacturability. Among the various strategies for reinforcing structures, bonding of high-strength composite carbon materials (FRP — Fiber-reinforced polymer) is becoming more and more popular in the world, especially for reinforced concrete structures, although application to metal structures is also quite common in Europe. But it should be noted that in Ukraine, unfortunately, this material is not yet widely used to strengthen metal structures. Problem Statement. The restoration of metal structures becomes necessary every time there are design, manufacturing or construction errors. Strengthening is also necessary in cases of long-term operation of buildings without timely maintenance and major repairs, insufficient strength of structural materials, as well as changes in weather conditions and current regulatory documents in Ukraine. So there is a need to strengthen metal structures with the most effective methods, both from the point of view of the reliability of building structures and from the point of view of profitability, which is influenced by the long shutdown of enterprises and the halt of the production process to carry out reconstruction work. Purpose. Investigate a modern method of reinforcing metal structures using high-strength carbon fibre-reinforced polymer (CFRP) materials in order to increase the bending capacity of a metal structural element, in particular, to check the reliability of adhesion of a metal beam to a reinforcing layer of TM «Mapei» composite material, which is glued using epoxy-based glue. Methods of research. Experimental testing of metal I-beams reinforced with external reinforcement by gluing high-strength carbon-based material (CFRP) TM «Mapei» by means of a static concentrated load in the middle of the beam span. Results. By analyzing the results of the experimental test, data were obtained indicating that after the inclusion of the carbon fibre-reinforced polymer in the operation, the percentage decrease in vertical deflection at a load of 75 kN was 39.5 %, and the value of the prmissible load, taking into account the stiffness condition (checking of building structures the established conditions of limiting deflections), increased by 11.8 %. When testing the phenomena of delamination of the composite from the base was not detected. Conclusions. Reinforcement of steel beams with a carbon fibre-reinforced polymer material led to a decrease in element deformations and, as a consequence, to the possibility of increasing the bearing capacity. An experimental test confirms the theoretical calculations to maximize the bearing capacity of a metal beam using the fibre-reinforced polymer material. A significant effect from the reinforcement of metal structures with composite materials can be achieved when strengthening the building structures of large-span buildings and structures, when reinforcing by traditional methods, they require complex design solutions, high labor costs, stopping the production process to perform reinforcement work, when the weight of the reinforcing structure is often significant.