This paper presents a 2-phase 3-level (2P3L) envelope tracking supply modulator (ETSM) for a 20 MHz LTE RF power amplifier (PA) as a solution for the envelope tracking (ET) system. This 2P3L ETSM that is composed of only switching converters achieves high efficiency, fast transient response, and a small output current ripple. To properly operate the proposed 2P3L ETSM, 4 PWM signals with a 90° phase shift from each PWM signal are required without any mismatch between duty cycles. To remove the mismatch, a time-division multiplexing comparator (TDMC) and a duty-cycle calibrator (DCC) are proposed. Thanks to the proposed techniques, the proposed ETSM fabricated in 0.18 μm CMOS achieved the highest peak dynamic efficiency of 88.6% with a LTE20 signal, which is superior to the state-of-the-art systems.
14 November 2022 in IEEE Transactions on Industrial Electronics
The energy harvesting interface circuit is proposed for wind-driven triboelectric nanogenerator (WD-TENG). To extract power from the WD-TENG maximally and deliver power to the output (battery) efficiently, a rectifier-reusing bias-flip (RRBF) technique and a multiphase reconfigurable switched-capacitor converter (MRSCC) are developed. In the RRBF, the low-side switches of the rectifier are reused as switches for bias-flip without additional components. The MRSCC delivers power to the battery efficiently by reducing switching loss including overlap loss. Furthermore, the MRSCC maintains a rectified voltage ( V RECT ) as high as a breakdown voltage ( VBR ) of a switch by adaptive conversion control and multiphase operation to extract maximized power from the WD-TENG in a given process, even if the battery voltage is varied from 2.7 to 4.2 V. Owing to the proposed techniques, the maximum extracted power to the output is 238 μW and peak power delivering efficiency of the MRSCC is 79.3%. The chip was fabricated in 0.18 μm BCD process.
8 October 2018 in IEEE Transactions on Industrial Electronics
A resonant current-mode receiver is studied to charge low-voltage batteries wirelessly for supplying medical implantable systems. To increase efficiency, the root-mean-square (RMS) current in the LC tank of the receiver (RX) is reduced by using a voltage-boosted current-mode (VBCM) receiver. This receiver combines the conventional current-mode receiver with a switched-capacitor converter to boost the voltage instantaneously at the switching node ( $V_X$ ) of coil. Owing to the suggested technique, the receiver directly charges a low-voltage battery while maintaining a small RMS current without using a complex voltage regulator. The receiver achieves an efficiency as high as 84.7% with a 1.1 V battery while operating at the resonant frequency ( $f_{reso}$ ) of 6.78 MHz. The power delivered to the output ( $P_{o}$ ) is in the range from 1.5 mW to 50 mW. The VBCM receiver was fabricated by 180 nm CMOS technology with a total active area of $\rm0.22 mm^2$
6 April 2018 in IEEE Transactions on Power Electronics
This letter presents a wireless power transfer (WPT) system for wristband device charging. By using dual receiver coils with power switches in an interleaved manner, the proposed WPT system can simultaneously operate to accumulate energy from the primary coil and transfer the previously accumulated energy to the battery in each coil. As a result, the WPT efficiency can be increased with the small coils, even at high load resistance. The proposed WPT system is theoretically analyzed by a lumped circuit model and verified by measurement using prototype boards. Compared with the conventional WPT structure that uses one receiver coil (2 cm × 5 cm), the proposed WPT system with two receiver coils (each 2 cm × 2.5 cm) achieved a 6.67% end-to-end power efficiency improvement at the output resistance of 100 Ω under the same condition of the coil dimension and the resonant frequency of 140 kHz.
2 August 2022 in IEEE Journal of Solid-State Circuits
This article presents an energy-harvesting (EH) interface chip system for triboelectric nanogenerators (TENGs). Despite TENG’s numerous advantages, its high open-circuit voltage and large parasitic capacitance ( $C_{{T}})$ give a considerable burden to design TENG-EH integrated circuits (ICs). In this work, a scalable multi-chip-stacked bias-flip (MCS-BF) technique is proposed to harvest TENG energy with ultra-high extraction voltage, exceeding an LDMOS transistor’s voltage-rating limit ( $\sim$ 70 V). Even in multi-chip-stacked structures, the MCS-BF utilizing a series inductor cancels the energy loss caused by $C_{{T}}$ . Furthermore, a practical solution to synchronize chip-to-chip control signals without over-voltage stress is also presented, even when many chips are daisy-chained together. The proposed TENG-EH chips were fabricated in a 0.18- $\mu $ m BCD process. In experiments with a real wind-TENG, an extremely high extraction voltage of 130 V (195 V) was successfully demonstrated with two (three) MCS-BF chips. Also, a harvested power per TENG area was measured to be 96.4 $\mu $ W/cm $^{2}$ with a two-chip solution, which is 4 $\times$ higher than previous state-of-the-art TENG-EH chips. The conversion from rectified input to regulated (battery voltage) output attained a measured peak efficiency of 70.7%. The proposed TENG-EH multi-chip system offers a 3.14 $\times$ power extraction gain (figure of merit).
29 September 2017 in IEEE Transactions on Power Electronics
This paper presents a phase-cut dimmable AC-DC buck LED driver for electrolytic capacitor-less LED lighting applications. In the driver, the sine-reference band (SRB)-controlled average current technique is proposed to perform rectified sine-average current control and phase-cut dimming control. The rectified sine-average current control can regulate the average value of sine-wave LED current, maintaining a high power factor (PF) over a wide range of AC input voltage and output LED load. The phase-cut dimming control not only makes the LED driver compatible with two types of phase-cut dimmers, namely, leading-edge and trailing-edge dimming types, but also eliminates visible dimming flicker at the AC line frequency. Fabricated in a 0.35 μm CMOS process, experimental results show the line regulation of ± 2.36 % over 90 to 260 VAC and the load regulation of ± 0.65 % within the load range of 10 to 36 LEDs. The PF exceeds 0.95 under all conditions, and the peak efficiency of 90.7 % is achieved. The analysis of the flicker frequency verifies that the proposed dimmable LED driver completely eliminates visible flicker owing to the phase dimming variations without an output electrolytic capacitor.