6 March 2018 in IEEE Transactions on Electron Devices
A millimeter (mm) wave amplifier that combines both high-power output and a wide bandwidth would enable dramatic improvements in areas where high-power radio signals with significant information content are required. However, to date, the only available devices are either high-power vacuum electronic devices with limited bandwidths, or larger bandwidth semiconductor amplifiers with low-power output. Here, we show a new design of a vacuum electronic traveling-wave tube amplifier that has a measured output power of 107 W with a 3-dB bandwidth of 6 GHz centered on 200 GHz. The power-bandwidth product of this amplifier is 642 W-GHz. These results provide a demonstration of a high-power mm-wave source with significant bandwidth. This device is readily scalable to other frequency bands, particularly those in the mm- and sub-mm-wave frequency bands from 100 GHz to 1 THz.
7 April 2022 in IEEE Transactions on Microwave Theory and Techniques
We report a packaging approach for building mm-wave massive multiple-input–multiple-output (MIMO) transmitter arrays in tiles. A single-channel 135-GHz transmitter, having a 22-nm fully-depleted (FD)-silicon on insulator (SOI) CMOS IC for baseband-RF conversion, an InP HBT power amplifier, and a linear microstrip patch antenna array, all packaged on a low-permittivity ceramic interposer (Kyocera GL771, $\varepsilon _{r}=5.2\,\,\text {and}\,\,\delta =0.003$ ), had 27.5-dBm measured effective isotropic radiated power (EIRP) at saturation and showed 8.5% error vector magnitude (EVM) during 30-Gb/s, 64 quadratic-amplitude modulation (QAM) transmission. An eight-channel transmitter MIMO array tile module constructed on an low-temperature-cofired ceramic (LTCC) interposer, with the same antennas and ICs, after calibration and under the control of a field-programmable gate array (FPGA), had 38.5-dBm measured EIRP at saturation and showed −13-dB EVM in 1.92-Gb/s 16 QAM transmission. Steerable two-simultaneous beam transmission was demonstrated at 34-dBm peak EIRP per beam.
12 February 2008 in Journal of Lightwave Technology
In this paper, we present a coherent receiver based on an optical phase-locked loop (PLL) for linear phase demodulation. The receiver concept is demonstrated at low frequency. For high-frequency operation, monolithic and hybrid integrated versions of the receiver have been developed and experimentally verified in an analog link. The receiver has a bandwidth of 1.45 GHz. At 300 MHz, a spurious free dynamic range (SFDR) of 125 dB ldr Hz2/3 is measured.
1 July 2011 in Journal of Vacuum Science & Technology B
The influence of different gate metal deposition processes on the electrical characteristics of dielectric/III-V interfaces is investigated. Al2O3 and HfO2 dielectrics are grown on In0.53Ga0.47As channels and top metal electrodes are deposited by either thermal evaporation or electron beam deposition. It is shown that metal-oxide-semiconductor capacitors with electron beam evaporated electrodes exhibit substantially larger midgap interface trap densities than those with thermally evaporated electrodes. The damage caused by electron beam metallization can be mitigated by subsequent, long anneals in forming gas.
29 April 2021 in IEEE Transactions on Wireless Communications
This paper investigates the effect of oscillator phase noise on a multiuser millimeter wave (mmWave) massive MIMO uplink as we scale up the number of base station antennas, fixing the load factor, defined as the ratio of the number of simultaneous users to the number of base station antennas. We consider a modular approach in which the base station employs an array of subarrays, or “tiles.” Each tile supports a fixed number of antennas, and can therefore be implemented using a separate radio frequency integrated circuit (RFIC), with synchronization across tiles accomplished by employing a phased locked loop in each tile to synthesize an on-chip oscillator at the carrier frequency by locking on to a common lower frequency reference clock. Assuming linear minimum mean squared error (LMMSE) multiuser detection, we provide an analytical framework that can be used to specify the required power spectral density (PSD) mask for phase noise for a target system performance. Our analysis for the phase noise at the output of the LMMSE receiver indicates two distinct effects: self-noise for each user which is inversely proportional to the number of tiles, and cross-talk between users which is insensitive to the number of tiles, and is proportional to the load factor. These analytical predictions, verified by simulations for a 140 GHz system targeting a per-user data rate of 10 Gbps, show that tiling is a robust approach for scaling. Numerical results for our proposed design approach yield relatively relaxed specifications for phase noise PSD masks.
7 June 2010 in IEEE Microwave and Wireless Components Letters
This letter presents an inductor-loaded 2:1 regenerative frequency divider operating up to 331.2 GHz in an InP HBT process, which, to the best of authors' knowledge, is the fastest frequency divider reported thus far. On-wafer measurement shows that the divider is operating from 304.8 GHz to 331.2 GHz, with output power from -27 dBm to -12.3 dBm (no probe loss correction), while dissipating 85.5 mW from -4.1 V and -3.3 V supplies.