10 May 2021 in SN Applied Sciences
Coatings are used as practical solutions against the intrusion of corrosive ions into concrete structures, particularly, in the harsh marine environment. In the present study, the effectiveness of using cement-based and geopolymer-based coatings produced using by-product materials has been evaluated. Silica fume and GGBFS at their optimum dosages were incorporated into mortar mixtures as a cement replacement, and mixtures of NaOH or KOH and sodium silicate solutions were used in the alkali-activated mortars. Shrinkage test, RCMT, and capillary absorption test as common experiments for durability analysis, as well as tests related to the mechanical and bonding properties including compressive strength test, pull-off test, and shear bonding strength test were carried out on the specimens. According to the results, both geopolymer and cement-based mortars improved the compressive and bonding strengths, and chloride diffusion resistance of coatings compared to the OPC mortar. Silica fume was found to be more effective in the strength development of mortars at young ages, while GGBFS was more responsible for acting as a filler and producing further gel in the older ages. The major drawback with geopolymer mortars is the high rate of water absorption and shrinkage coefficient in the early hours, which shows the importance of curing of these mortars at young ages. Overall, the mix design produced with 30% GGBFS and 7.5% silica fume showed the highest durability and mechanical properties and proved to be more compatible with the harsh environment of the Persian Gulf.
27 May 2024 in Transportation Research Record: Journal of the Transportation Research Board
The use of recycling agents (RAs), along with recycled asphalt pavement (RAP) modifiers, has been increasing over recent years. However, the field performance of asphalt mixtures containing high-RAP materials modified with RAs has raised some concerns with the long-term performance of RAs. This study evaluated the laboratory and field performance of high-RAP mixtures with and without bio-oil RA. Five sets of plant-produced specimens were collected: 1) plant-produced laboratory-compacted; 2) field-compacted, cored after paving; 3) field-compacted, cored after one year; 4) field-compacted, cored after two years; and 5) field-compacted, cored after three years. The Hamburg wheel tracking test was used to evaluate the specimens’ resistance to rutting and moisture damage, while the semi-circular bending test was performed to examine the cracking resistance of specimens. The laboratory test results showed that using the bio-oil RA increased cracking resistance and decreased rutting and moisture damage resistance of the RAP-blended mixtures. However, after one and two years of exposure to environmental conditions and traffic loads, the specimens modified by RA showed better moisture damage and rutting resistance. The cracking resistance of laboratory and field-aged specimens, estimated by flexibility index, implied that the bio-oil RA used in this study could not provide long-term improvement for the RAP-blended mixtures. Field observations suggest that using bio-oil RA may have resulted in inferior pavement performance compared with the control section. However, drawing conclusions based on just two years of data might yield inconclusive results. Longer field performance monitoring is, therefore, warranted for a more comprehensive analysis.
17 December 2025 in Construction and Building Materials
AFAdalberto Leandro Faxina
8 September 2025 in Transportation Research Record: Journal of the Transportation Research Board
This study examined the effectiveness of the laboratory short-term aging process for warm mix asphalt (WMA) binders using response surface methodology (RSM) with various combinations of aging parameters: time, temperature, airflow, and binder weight. The research aimed to enhance understanding of aging parameter efficacy and propose a modified laboratory short-term aging protocol that accurately simulates plant short-term aging in WMA binders. To this end, three WMA mixtures produced at 135°C were collected from plants, and their asphalt binders were extracted and recovered. Virgin binders from the same projects were also obtained and two of them aged in a rolling thin film oven at different combinations of aging parameters, designed by RSM. High-temperature performance grade (PG) and carbonyl index were used as model responses to quantify laboratory aging levels. These parameters were also assessed in the plant extracted binders to establish target values. The statistical analysis revealed significant effects of time, temperature, and weight, as well as their interactions, on key rheological and chemical properties of binders, while the airflow rate effect within the studied range was found to be insignificant. A modified protocol for laboratory short-term aging of WMA binders was developed, showing consistency with plant short-term aged binder results. The model was successfully validated using chemical and rheological assessments of a third binder aged with the proposed protocol.