1 June 2018 in Nanotechnology
We fabricated electrochemical metallization cells using a GaLaSO solid electrolyte, an InSnO inactive electrode and active electrodes consisting of various metals (Cu, Ag, Fe, Cu, Mo, Al). Devices with Ag and Cu active metals showed consistent and repeatable resistive switching behaviour, and had a retention of 3 and >43 days, respectively; both had switching speeds of <5 ns. Devices with Cr and Fe active metals displayed incomplete or intermittent resistive switching, and devices with Mo and Al active electrodes displayed no resistive switching ability. Deeper penetration of the active metal into the GaLaSO layer resulted in greater resistive switching ability of the cell. The off-state resistivity was greater for more reactive active metals which may be due to a thicker intermediate layer.
22 May 2019 in Journal of Materials Science: Materials in Electronics
2 July 2024 in Journal of Applied Physics
This work presents the excess noise and thermoelectric (Seebeck) measurements on polycrystalline vanadium dioxide (VO2) thin films. Noise spectral power density (SPD) of current fluctuations in the semiconducting (SC) phase had a typical flicker noise (f−γ) characteristic with an average slope parameter γ of 1.13. Normalized SPD (Sn) values obtained in the SC-phase indicate that the noise originates in the bulk of the film. On the contrary, in the metallic (M)-phase, γ values were greater than unity, and the observed Sn values indicated that the origin of the noise is most likely from the contacts or surface rather than the bulk. A general decrease was observed in Sn by a factor of 4–5 from the SC- to M-phase. Moreover, Sn in the SC-phase showed no temperature dependence. An interpretation based on the number of charge carrier fluctuations in Hooge's model led to an unrealistically high Hooge parameter and had to be ruled out. We propose that the fluctuations are related to the mobility fluctuations of carriers arising primarily from grain-boundary scattering which explains the observed characteristics well. The Seebeck coefficients (S) obtained under both heating and cooling schedules showed the n-type nature of magnetron-sputtered VO2 films in the SC-phase. Differently, in the M-phase, the S value was positive. The S values obtained from the cooling schedule signified the low percolation threshold of the metal-to-insulator transition already demonstrated for VO2 thin films grown on r-cut sapphire using the Efros–Shklovskii percolation model.
7 March 2023 in Journal of Materials Science: Materials in Electronics
Seebeck measurements of n-type amorphous germanium telluride thin films (100 nm) containing oxygen and implanted with Bismuth (Bi) have been studied under dark and monochromatic light conditions from 1800 to 400 nm. The Bi-doped film has a negative Seebeck coefficient indicating its n-type nature that results from the implantation compared to the p-type undoped films. Upon illumination with monochromatic light across the near-infrared and visible region the magnitude of the measured Seebeck voltage increases (becomes more negative). This increase in Seebeck coefficient displays distinctive behaviours in different spectral regions and is caused by the inclusion of Bi ions as foreign impurities. Furthermore, the Seebeck coefficients are used to determine the film electrical properties and enable, along with complementary characterisation including X-ray photoelectron spectroscopy, electronic band diagrams to be proposed for before and after Bi ion implantation. The photo-Seebeck technique is utilised for the first time to probe the trap states created due to the implantation, providing an understanding of the mechanisms behind non-equilibrium carrier-type reversal in an amorphous system, including the modification of electronic and optoelectronic properties such as the optical bandgap.
29 October 2020 in Journal of Materials Science: Materials in Electronics
The measurement of the Seebeck coefficient of thin film (100 nm) amorphous germanium telluride containing ~ 31% oxygen under dark conditions and when exposed to monochromatic light in the 400 nm to 1800 nm wavelength region is reported. Exposure of the films to light is found to reduce the absolute value of the Seebeck coefficient compared to that measured in the dark. Furthermore, the magnitude of this reduction displays a distinctive spectral dependence over the wavelength range covered. The observed behaviour suggests that these measurements provide a method determining the optical bandgap of thin amorphous chalcogenide films. Further analysis of the data, along with that of X-ray photoelectron spectroscopy and photoconductivity studies, is used to determine the presence of sub-bandgap defect states and their role in determining the optical response of the Seebeck coefficient.