13 July 2020 in Energy & Environmental Materials
FMFrancis Peter Moissinac
+2
Conventional electrode preparation techniques of supercapacitors such as tape casting or vacuum filtration often lead to the restacking or agglomeration of two‐dimensional (2D) materials. As a result, tortuous paths are created for the electrolyte ions and their adsorption onto the surfaces of the active materials can be prevented. Consequently, maintaining high rate performance while increasing the thickness of electrodes has been a challenge. Herein, a facile freeze‐assisted tape‐casting (FaTC) method is reported for the scalable fabrication of flexible MXene (Ti3C2Tx) supercapacitor electrode films of up to 700 μm thickness, exhibiting homogeneous ice‐template microstructure composed of vertically aligned MXene walls within lamellar pores. The efficient ion transport created by the internal morphology allows for fast electrochemical charge–discharge cycles and near thickness‐independent performance at up to 3000 mV s−1 for films of up to 300 μm in thickness. By increasing the scan rate from 20 to 10,000 mV s−1, Ti3C2Tx films of 150 μm in thickness sustain 50% of its specific capacitance (222.9 F g−1). When the film thickness is doubled to 300 μm, its capacitance is still retained by 60 % (at 213.3 F g−1) when the scan rate is increased from 20 to 3000 mV s−1, with a capacitance retention above 97.7% for over 14,000 cycles at 10 A g−1. They also showed a remarkably high gravimetric and areal power density of 150 kW kg−1 at 1000 A g−1 and 667 mW cm−2 at 4444 mA cm−2, respectively. FaTC has the potential to provide industry with a viable way to fabricate electrodes formed from 2D materials on a large scale, while providing promising performance for use in a wide range of applications, such as flexible electronics and wearable energy storage devices.
17 March 2020 in Journal of Physics: Materials
12 September 2016 in Industrial Lubrication and Tribology
Purpose: This paper aims to synthesize nanostructured flower-like molybdenum disulphide (MoS2) particles and evaluate their suitability to act as additives for lubricants. Design/methodology/approach: A hydrothermal method without any surfactant successfully produced 250 nm mean diameter Nanostructured flower-like MoS2 particles. The resulting product was then solvothermally treated with absolute ethanol producing lipophilic powder particles which after being dispersed in two different lubricants were tribologicaly characterized by using a pin-on-disk tribometer geometry with reciprocal movement under immersion. Findings: The influence on the stability and the coefficient of friction of the nano-oils is shown to be strongly dependent on their molecular structure. After 1 h of tribological testing, a ramified polyolester oil with 1 Wt.% of MoS2 nanoflowers did not show decrease in its average coefficient of friction, while an additive naphthenic oil with the same concentration of nanoparticles showed a decrease of 86 per cent. Originality/value: In this paper, nanostructured flower-like MoS2 synthesized by the hydrothermal method was dispersed in lubricating oils to study its stability and tribological properties. To ensure good stability of the nano-oils, the particles were solvothermally treated with absolute ethanol to dehydrate and lipophilize them. A ramified polyolester-based nano-oil with 1 Wt.% of MoS2 nanoflowers showed no decrease in its steady state coefficient of friction, while a naphthenic-based nano-oil with the same concentration of nanoparticles presented a remarkable 86 per cent reduction.
1 December 2015 in Journal of Physics and Chemistry of Solids
1 March 2020 in Journal of Magnetism and Magnetic Materials
1 November 2018 in Journal of Alloys and Compounds
VSVictor Alexandre Veit Schmachtenberg
Victor Alexandre Veit Schmachtenberg