Thomas Modes

Thomas Modes

Auto-generated profile, based on publicly available information

Thomas Modes

Fraunhofer Institute for Electron Beam and Plasma Technology (FEP) , Winterbergstr. 28, Dresden 01277

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 April 2026 in Surfaces and Interfaces
Verified
Journal Article
Open access
HNH. Nizard
H. Nizard
ASAnna Sytchkova
Anna Sytchkova
JYJ. Yang
J. Yang
DGD. Gloess
D. Gloess
UHU. Hartung
U. Hartung
EHE. von Hauff
E. von Hauff

27 April 2026 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Open access
BSBert Scheffel
Bert Scheffel
OZOlaf Zywitzki
Olaf Zywitzki
SSStefan Saager
Stefan Saager
TMThomas Modes
Thomas Modes
LDLudwig Decker
Ludwig Decker
RWRobert Werberger
Robert Werberger
Anodic vacuum arc evaporation was applied to deposit ta-C layers with thicknesses of 1.3–2.2 μm at high deposition rates of up to 18 nm/s. Building on prior work that was limited to a thickness of 0.8 μm due to high heat flux and adhesion issues, substrates with a high heat capacity and adhesion-promoting interlayers were used. Nanoindentation tests revealed hardness values ranging from 71 to 84 GPa and Young’s moduli ranging from 717 to 862 GPa for these layers. Raman spectrometry revealed an sp3 content of 68% to 75%. The layers are free of arc-typical droplets and have a very smooth surface. These results demonstrate that anodic vacuum arc evaporation, when combined with targeted thermal management and interlayer design, provides a scalable method of producing ta-C coatings for challenging mechanical or chemical engineering applications.

26 February 2026 in Science and Technology of Advanced Materials
Verified
Journal Article
Open access
PJPascal Jundt
Pascal Jundt
OZOlaf Zywitzki
Olaf Zywitzki
TMThomas Modes
Thomas Modes
SBSagar Baitule
Sagar Baitule
RARobert Arndt
Robert Arndt
BSBastian Siepchen
Bastian Siepchen
Incorporation of selenium within cadmium telluride to form the CdSexTe1-x alloy has enabled higher device efficiencies in photovoltaic applications through improved passivation and current collection. Recent investigations of this alloy have simultaneously indicated significant potential for further performance gains as well as potentially serious detrimental characteristics. Exploring how best to utilize this important material requires consistent, configurable film deposition. Absorber layers are often deposited by close-space sublimation, which can produce high-quality films at large scale. It has previously been demonstrated that close-space sublimation of CdSeTe material directly is inconvenient and inflexible; therefore, an alternative method with greater consistency and control over film composition is sought. In this work, CdSeTe films were formed by close-space sublimation of alternating CdSe and CdTe layers followed by a high-temperature annealing in the presence of CdCl2. Under the optimal deposition conditions, this technique was shown to produce high-quality films of CdSeTe with homogeneous elemental distribution, uniform grain size, and low roughness. However, this method also exhibited a significant tendency to form numerous voids which largely persist after CdCl2 annealing. The source of this porosity was investigated and determined to primarily be resublimation of CdTe during the higher-temperature deposition of the CdSe layers. The process window to prevent voiding was observed to be rather small; while this would be a significant detriment in a production setting, it is less important in the targeted application for this approach, which is fundamental material and device investigations.

4 February 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
HNHarry Nizard
Harry Nizard
ASAnna Sytchkova
Anna Sytchkova
JYJiye Yang
Jiye Yang
DGDaniel Gloess
Daniel Gloess
UHUllrich Hartung
Ullrich Hartung
EHElizabeth von Hauff
Elizabeth von Hauff
A vacuum deposition process for nanocomposite coatings, designed using a combination of inert gas phase condensation (GPC) and plasma-enhanced chemical vapor deposition (PE-CVD) processes, was demonstrated. Metal nanoparticles (NPs) were synthesized through the condensation of sputtered atomic vapor produced by gas flow sputtering (GFS). A low-pressure PE-CVD source was used for the direct encapsulation of the NPs inside plasma polymer layers obtained from organic precursors. Samples were transferred directly between NP and matrix sources, achieving safe-by-design in vacuo fixation of NPs inside multilayer nano-composite coatings. PE-CVD layers were investigated by Fourier-transform infrared (FTIR) spectroscopy. Then, PE-CVD combined with NPs multilayer nanocomposite coatings were investigated by cross-section scanning electron microscopy (SEM), variable angle UV-NIR ellipsometry and UV-Vis spectrometry. We observed typical localized surface plasmon resonance (LSPR) absorption peaks in the UV-Vis spectra and a redshift with increasing particle size, as well as a broadening of absorption peaks with increasing Ag content, confirming the plasmonic activity of deposited nanocomposite thin films required for optical and sensor applications.

12 June 2026 in Vacuum
Verified
Journal Article
Closed access
HNH. Nizard
H. Nizard
SRS. Rauer
S. Rauer
DGD. Gloess
D. Gloess
ADA. Delan
A. Delan
TMT. Modes
T. Modes
EHE. von Hauff
E. von Hauff