24 December 2025 in The European Physical Journal C
Volume 1 of the FCC Feasibility Report presents an overview of the physics case, experimental programme, and detector concepts for the Future Circular Collider (FCC). This volume outlines how FCC would address some of the most profound open questions in particle physics, from precision studies of the Higgs and EW bosons and of the top quark, to the exploration of physics beyond the Standard Model. The report reviews the experimental opportunities offered by the staged implementation of FCC, beginning with an electron-positron collider (FCC-ee), operating at several centre-of-mass energies, followed by a hadron collider (FCC-hh). Benchmark examples are given of the expected physics performance, in terms of precision and sensitivity to new phenomena, of each collider stage. Detector requirements and conceptual designs for FCC-ee experiments are discussed, as are the specific demands that the physics programme imposes on the accelerator in the domains of the calibration of the collision energy, and the interface region between the accelerator and the detector. The report also highlights advances in detector, software and computing technologies, as well as the theoretical tools/reconstruction techniques that will enable the precision measurements and discovery potential of the FCC experimental programme. The content and structure of this report are guided by the scope and priorities defined in the mandate of the FCC Feasibility Study. It is therefore not intended to serve as an exhaustive review of the full physics potential of FCC. Several topics, already covered in earlier reports such as the FCC CDR, are not reiterated here or are addressed only briefly, in alignment with the study’s focus. This volume reflects the outcome of a global collaborative effort involving hundreds of scientists and institutions, aided by a dedicated community-building coordination, and provides a targeted assessment of the scientific opportunities and experimental foundations of the FCC programme.
1 May 2025 in Physical Review Accelerators and Beams
An important upgrade has been deployed for the collimation system of the Large Hadron Collider (LHC) for lead-ion beams that are already planned to reach their high-luminosity target intensity upgrade in the ongoing LHC Run 3 (2022–2026). While certain effects like e-cloud, beam-beam, impedance, injection, and dump protection are relaxed with ion beams, halo collimation becomes an increasing challenge, as the conventional multistage collimation system is about two orders of magnitude less efficient than that for proton beams. Ion fragments scattered out of the collimators in the betatron cleaning insertion risk quenching the cold dipole magnets downstream and may represent performance limitations. Planar channeling in bent crystals has been proven effective for high-energy heavy ions. A crystal collimation system was integrated into the LHC as a baseline solution for collimation in the High-Luminosity LHC (HL-LHC) era. In this paper, simulation and measurement results demonstrating the observation of channeling of heavy-ion beams and improvement in collimation cleaning in the multi-TeV energy regime are presented. The efficiency of the collimation scheme foreseen for the HL-LHC is presented. The highlights of the collimation performance in 2023, when crystal collimation was successfully deployed operationally for the first time, are also presented.
1 May 2024 in Journal of Instrumentation
The High Luminosity (HL-LHC) project aims to increase the integrated luminosity of CERN's Large Hadron Collider (LHC) by an order of magnitude compared to its initial design. This requires a large increase in bunch intensity and beam brightness compared to the first three LHC runs, and hence poses serious collective-effects challenges, related in particular to electron cloud, instabilities from beam-coupling impedance, and beam-beam effects. Here, we present the associated constraints and the mitigation measures proposed to achieve the baseline performance of the upgraded LHC machine. We also discuss the interplay of these mitigation measures with other aspects of the accelerator, such as optics, physical and dynamic apertures, the collimation system, and crab cavities. Additional potential sources of intensity limitations are also briefly discussed.
2 December 2025 in The European Physical Journal C
This study investigates the performance of bent silicon crystals intended to channel hadrons in a fixed-target experiment at the Large Hadron Collider (LHC). The phenomenon of planar channelling in bent crystals enables extremely high effective bending fields for positively charged hadrons within compact volumes. Particles trapped in the potential well of high-purity, ordered atomic lattices follow the mechanical curvature of the crystal, resulting in macroscopic deflections. Although the bend angle remains constant across different momenta (i.e., the phenomenon is non-dispersive), the channelling acceptance and efficiency still depend on the particle momentum. Crystals with lengths in the range of 5 to 10 cm, bent to angles between 5 and 15 mrad, are under consideration for measurements of the electric and magnetic dipole moments of short-lived charmed baryons, such as the $$\varLambda _c^+$$ . Such large deflection angles over short distances cannot be achieved using conventional magnets. The principle of inducing spin precession through bent crystals for magnetic dipole moment measurements was first demonstrated experimentally in the 1990s. Building on this concept, experimental layouts are now being explored for implementation at the LHC. The feasibility of such measurements depends, among other factors, on the availability of crystals that exhibit the required mechanical properties to reach the necessary channelling performance. To address this, a dedicated machine experiment – TWOCRYST – has been installed in the LHC to carry out beam tests in the TeV energy range. The bent crystals for TWOCRYST were fabricated and tested using both X-ray diffraction and high-momentum hadron beams at 180 GeV/c at the CERN Super Proton Synchrotron (SPS) extraction lines. Two crystals based on established technologies were included in this test. In addition, a crystal bent via anodic bonding was tested for the first time with high-energy hadrons to assess its potential for future accelerator applications. This paper presents an analysis of the performance of the three tested crystals and, where possible, outlines key differences in their properties attributed to the respective bending techniques.
27 October 2025 in Physical Review Accelerators and Beams
The objective of the High Luminosity Large Hadron Collider (HL-LHC) upgrade is to attain an instantaneous luminosity that is 5 times greater than the design value of the LHC. This requires nearly 2 times higher beam intensity compared to the operational LHC value during Run 2 (2015–2018). Higher bunch intensity makes the beam more prone to coherent instabilities. To keep beam stability under control and preserve beam quality, it is therefore necessary to reduce the machine beam coupling impedance. The collimation system of the LHC is presently responsible for a significant portion of the total machine impedance budget. In this context, during the LHC long-shutdown 2 (LS2), the LHC machine has been upgraded with newly engineered low-impedance collimators whose absorbing jaws are made of molybdenum-graphite (MoGr) compared to the previously used carbon fiber composite (CFC). Secondary collimators are also coated with molybdenum (Mo) to further boost conductivity. In order to validate the benefits of the impedance reduction targeted at the collimators and to identify possible nonconformities, we performed a series of tune shift measurements on the newly installed primary and secondary collimators with LHC beams and quantified the agreement with predictions. As expected, the results show a significant reduction in the collimators’ impedance contribution. Additionally, the remaining discrepancy between measurements and predictions is investigated with 3D numerical simulations by using the Wakefield Solver of Computer Simulation Technology.
9 February 2026 in The European Physical Journal C