The High-Luminosity Large Hadron Collider (HL-LHC) project aims at extending the operability of the LHC by another decade and increasing by more than a factor of ten the integrated luminosity that the LHC will have collected by the end of Run 3. This will require doubling the beam intensity and reducing the transverse beam size compared to those of the LHC design. The higher beam brightness poses new challenges for machine safety, due to the large energy of 700 MJ stored in the beams, and for beam stability, mainly due to the collimator contribution to the total LHC beam coupling impedance. A rich research program was therefore started to identify suitable materials and collimator designs, not only fulfilling impedance reduction requirements but also granting adequate beam-cleaning and robustness against failures. The use of thin molybdenum coatings on a molybdenum–graphite substrate has been identified as the most promising solution to meet both collimation and impedance requirements, and it is now the baseline choice of the HL-LHC project. In this work we present the main results of the coating characterization, in particular addressing the impact of coating microstructure on the electrical resistivity with different techniques, from Direct Current (DC) to GHz frequency range.
31 December 2020 in Physical Review Accelerators and Beams
A destabilizing effect of the detuning impedance has been recently observed in simulations of the CERN Proton Synchrotron (PS) at the injection energy: while without the detuning impedance the instability is faster in the vertical plane as expected (due to the elliptical shape of the vacuum chamber), with detuning impedance the instability appears to be faster in the horizontal plane. In order to understand the detuning impedance destabilizing effect, we study the collective behavior for the simpler case of a coasting beam with PS-like parameters and a simplified impedance model. The analysis, carried out from both numerical and theoretical points of view, highlights a new destabilizing mechanism related to the coupling of slow and fast waves.
The Gamma Factory (GF) initiative proposes to use partially stripped ion (PSI) beams as drivers of a new type of high-intensity and high-energy (0.1–400 MeV) photon source. As part of the ongoing Physics Beyond Collider studies, initial beam tests were carried out in 2017 and 2018 at the SPS and LHC with partially stripped xenon and lead beams. This contribution discusses the results of these tests and the preparations for the next GF R&D step: the proof-of-principle experiment at the SPS to study interaction of PSI beams with the laser light
Beam Intercepting Devices (BIDs) are essential protection elements for the operation of the Large Hadron Collider (LHC) complex. The LHC internal beam dump (LHC Target Dump Injection or LHC TDI) is the main protection BID of the LHC injection system; its main function is to protect LHC equipment in the event of a malfunction of the injection kicker magnets during beam transfer from the SPS to the LHC. Several issues with the TDI were encountered during LHC operation, most of them due to outgassing from its core components induced by electron cloud effects, which led to limitations of the injector intensity and hence had an impact on LHC availability. The absorbing cores of the TDIs, and of beam intercepting devices in general, need to deal with high thermo-mechanical loads induced by the high intensity particle beams. In addition, devices such as the TDI — where the absorbing materials are installed close to the beam, are important contributors to the accelerator impedance budget. To reduce impedance, the absorbing materials that make up the core must be typically coated with high electrical conductivity metals. Beam impact testing of the coated absorbers is a crucial element of development work to ensure their correct operation. In the work covered by this paper, the behaviour of several metal-coated absorber materials was investigated when exposed to high intensity and high energy proton beams in the HiRadMat facility at CERN. Different coating configurations based on copper and molybdenum, and absorbing materials such as isostatic graphite, Carbon Fibre Composite (CfC) and Silicon Carbide reinforced with Silicon Carbide fibres (SiC-SiC), were tested in the facility to assess the TDI's performance and to extract information for other BIDs using these materials. In addition to beam impact tests and an extensive Post Irradiation Examination (PIE) campaign to assess the performance of the coatings and the structural integrity of the substrates, extensive numerical simulations were carried out.
The High Luminosity Large Hadron Collider (HL-LHC) project will upgrade the LHC machine to allow operation with increased luminosity for the experiments. In order to achieve this goal, different operational parameters of the machine need to be pushed beyond the present design values, including the stored beam energy. One of the main challenges related to the achievement of the upgraded performance is the beam collimation system and its contribution to the overall machine impedance budget. In this perspective, new low impedance collimators have been designed, fabricated, and installed in the LHC. In this study, we will present their detailed electromagnetic (EM) characterization by means of radio frequency (RF) measurements and EM simulations.
13 April 2023 in Physical Review Accelerators and Beams
The accurate calculation of the beam coupling impedance for particle accelerators is necessary to carefully assess the machine stability against impedance-driven collective effects. A first order evaluation of the beam coupling impedance is often done by means of analytical formulas and/or 2D numerical codes. The infinite length approximation is often used to simplify the calculation of the beam coupling impedance of accelerator elements. This is expected to be a reasonable assumption for devices whose length is greater than the transverse dimension but may be a less accurate approximation for segmented devices. In this work, we present the application of the mode matching method to the calculation of the transverse dipolar impedance of a cylindrical cavity loaded with a toroidal insert. By choosing different insert electromagnetic properties (permittivity, permeability, and conductivity) and dimensions, the model can represent a beam pipe, a thin insert, a lossy cavity, or a collimator for which the effect of the finite length is investigated. The method is successfully benchmarked against available analytical formulas, field-matching codes, and 3D commercial solvers. The proposed model allows for performing wide parametric scans and reaching accurate results, therefore becoming an essential tool for the impedance evaluation of accelerator devices.