1 January 2013 in AIP Conference Proceedings
MSMuhammad Abdul Hakim Shibghatallah
Muhammad Abdul Hakim Shibghatallah
Leaf colors of a plant can be used to identify stress level due to its adaptation to environmental change. For most leaves green-related colors are sourced from chlorophyll a and b. Chlorophyll concentration is normally measured using a spectrophotometer in laboratory. In some remote observation places, it is impossible to collect the leaves, preserve them, and bring them to laboratory to measure their chlorophyll content. Based on this need, measurement of chlorophyll content is observed through its color. Using CIE chromaticity diagram leaf_color information in RGB is transformed into wavelength (in nm). Paddy seed with variety name IR-64 is used in observation during its vegetation stage t (age of 0-10 days). Light exposure time τ is chosen as environmental change, which normally should be about 12 hours/day, is varied (0-12 hours/day). Each day sample from different exposure time is taken, its color is recorded using HP Deskjet 1050 scanner with 1200 dpi, and its chlorophyll content is obtained from absorption spectrum measured using Campspec M501 Single Beam UV/Vis Spectrophotometer after it is rinsed in 85 % acetone solution and the information from the spectrum is calculated using Arnon method. It has been observed that average wavelength of leaf color λavg is decreased from 570.55 nm to 566.01 nm as is measured for t = 1 - 10 days with τ = 9 hours/day, but chlorophyll concentration C is increased from 0.015 g/l to 3.250 g/l and from 0.000 g/l to 0.774 g/l for chlorophyll a and b, respectively. Other value of τ gives similar results. Based on these results an empirical relation between concentration of chlorophyll a Cc-a and its wavelength λavg can be formulated.
1 January 2012 in AIP Conference Proceedings
Composite of two kinds of grains is modeled in two-dimension and the elasticity is calculated using molecular dynamics method implementing Gear predictor-corrector of fifth order. It has been observed that same composite concentration can be represented by several configurations of the two kinds of grains. Simulation results show a peak or maximum value of a parameter proportional to Young's modulus, which quantitatively agrees with reported experiment results. Ratio of used in simulation has influenced average value of the mentioned parameter monotonically, it is increasing as the ratio increasing.Comment: 4 pages, 7 figures, submitted to ICPAP 201
23 August 2011 in Physics Education
4 December 2023 in Malaysian Journal of Fundamental and Applied Sciences
The relatively high cost of medical-grade electroencephalography (EEG) devices has pushed the production of low-cost wireless consumer-grade devices. Therefore, it is essential to assess the performance of wireless consumer devices to determine whether they are sufficient for medical purposes. This research assessed consumer-grade EEG (C-EEG) recording quality by quantitatively comparing the consumer-grade EEG with a medical-grade EEG device (M-EEG). Recording data from C-EEG and M-EEG were obtained from 20 male subjects in age 19-23 years old. Recording for both devices was done sequentially with similar methods of recording. Upon EEG recording, the subject is asked to sit in a chair facing the screen. EEG recording was performed when the subject was asked to open and close their eyes for 30 seconds each. Subsequently, subjects took a verbal memory test. This research compared the following parameters: power spectral density (PSD), full width at half max (FWHM) from PSD, and individual peak alpha frequency (IPAF) shift. P-value, standard error, mean absolute percentage error (MAPE) and mean squared error (MSE) were also obtained based on mentioned parameters. Based on the IPAF shift, it was concluded that C-EEG could read EEG signals against time well. Based on PSD and FWHM results, it was concluded that the C-EEG could not read EEG signal amplitudes well compared to the M-EEG device. The results of this research are important as a benchmark for carrying out further research using EEG, both medical and consumer-grade.
1 January 2012 in AIP Conference Proceedings
The composites made of bamboo apus fiber – epoxy resin and charcoal – tapioca starch with several compositions have been synthesized. Bamboo fiber powder as the rest of cutting process was refined and filtered by mesh 40 before used. Epoxy resin 1021A and hardener 1021B has been used as resin. The synthesis of epoxy resin-based composites was carried out via simple mixing method by adding adequate 70% ethanol solution before drying. The 100 mesh-filtered dry charcoal was mixed with tapioca mixture before it was pressed and dried to produce briquette composites. To study the compressive elastic modulus of the composites, pressure tests using Mark 10 Pressure Test Machine have been carried out. It was found that all the composites show maximum compressive elastic modulus at certain component compositions. The maximum elastic modulus for bamboo fiber-epoxy resin, charcoal – epoxy resin and charcoal-tapioca starch were observed at 52.9%, 56.3%, and 25.0% of mass fraction of bamboo fiber, charcoal and tapioca starch, respectively.
19 February 2014 in Advanced Materials Research
Epoxy is widely used primarily as a matrix material in the manufacture of Polymer Matrix Composites (PMC). Epoxy behavior under compression load has to be understood before the mechanical behavior of PMCs can be accurately predicted. Simulation model combined with experiment and image analysis are used to investigate internal response of epoxy resins polymeric materials subject to compressive loads. To investigate epoxy response to compressive load, small carbon-based material rods are inserted in the epoxy. The samples are held in one side and subjected to compressive load on the other side. All the samples swell at load sides. Image analysis on the carbon-based rods figures out the internal response, which seems to be isotropy in lateral direction. The results are compared to simulation results using Abaqus FEA. Similar condition is obtained when a brittle thin material is stuck to the top of the model.