Instrumentation and Computational Physics Research Group, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Jalan Ganesha 10 Bandung 40132, Indonesia
Auto-generated profile, based on publicly available information
Suprijadi Suprijadi
Instrumentation and Computational Physics Research Group, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Jalan Ganesha 10 Bandung 40132, Indonesia
Single-atom catalysis, which utilizes single atoms as active sites, is one of the most promising ways to enhance the catalytic activity and to reduce the amount of precious metals used. Platinum atoms deposited on graphene are reported to show enhanced catalytic activity for some chemical reactions, e.g. methanol oxidation in direct methanol fuel cells. However, the precise atomic structure, the key to understand the origin of the improved catalytic activity, is yet to be clarified. Here, we present a computational study to investigate the structure of platinum adsorbed on graphene with special emphasis on the edges of graphene nanoribbons. By means of density functional theory based thermodynamics, we find that single platinum atoms preferentially adsorb on the substitutional carbon sites at the hydrogen terminated graphene edge. The structures are further corroborated by the core level shift calculations. Large positive core level shifts indicate the strong interaction between single Pt atoms and graphene. The atomistic insight obtained in this study will be a basis for further investigation of the activity of single-atom catalysts based on platinum and graphene related materials.
We present a density functional theory study of atomic and molecular adsorption on a single Pt atom deposited at the edges of graphene. We investigate geometric and electronic structures of atoms (H, C, N, and O) and molecules (O2, CO, OH, NO, H2O, and OOH) on a variety of Pt deposited graphene edges and compare the adsorption states with those on a Pt(111) surface and on a Pt single atom. Furthermore, using the calculated adsorption energy and simple kinetic models, the catalytic activities of a Pt single-atom catalyst for the oxygen reduction reaction and CO oxidation are discussed.
The extensive uses of the air filters have encouraged the advancement of air filter technology on both fabrication and characterization. Due to the high demand to those filters, the quality assessment to the filters are massively needed with a lower test cost and accessible. We developed a personal air filter test (PAFT) system for measuring the filter pressure drop, efficiency, and quality factor. The PAFT system utilized a PM sensor (Sharp, GP2Y1010AU0F) for measuring the filtration efficiency. Accordingly, performance evaluation and optimization to the PM sensor were done to guarantee their compatibility for this application. The performance evaluation studied the sensor output responses to sampling flow, particle diameter, and PM sources. We also improved the sensor sensitivity. The experimental results show that the sensor has no significant influences on the sampling flow. The sensor output was highly dependent on the particle size and PM source, but their response curves remained linear, which was an advantage for filter efficiency measurement. We measured the efficiency of nanofiber filters having various efficiencies, and comparing the results to reference efficiency as measured by a CPC (TSI, 3772). The test resulted in a filtration coefficient (Kf), which was used to correct the PAFT efficiency measurement results. We also conducted the test to some commercial mask filters, and the filtration efficiency measurement results showed a good agreement to the reference with a small average error of about 2.5%. The complete design of the PAFT and experimental methods will be discussed in detail.
The relatively high cost of medical-grade electroencephalography (EEG) devices has pushed the production of low-cost wireless consumer-grade devices. Therefore, it is essential to assess the performance of wireless consumer devices to determine whether they are sufficient for medical purposes. This research assessed consumer-grade EEG (C-EEG) recording quality by quantitatively comparing the consumer-grade EEG with a medical-grade EEG device (M-EEG). Recording data from C-EEG and M-EEG were obtained from 20 male subjects in age 19-23 years old. Recording for both devices was done sequentially with similar methods of recording. Upon EEG recording, the subject is asked to sit in a chair facing the screen. EEG recording was performed when the subject was asked to open and close their eyes for 30 seconds each. Subsequently, subjects took a verbal memory test. This research compared the following parameters: power spectral density (PSD), full width at half max (FWHM) from PSD, and individual peak alpha frequency (IPAF) shift. P-value, standard error, mean absolute percentage error (MAPE) and mean squared error (MSE) were also obtained based on mentioned parameters. Based on the IPAF shift, it was concluded that C-EEG could read EEG signals against time well. Based on PSD and FWHM results, it was concluded that the C-EEG could not read EEG signal amplitudes well compared to the M-EEG device. The results of this research are important as a benchmark for carrying out further research using EEG, both medical and consumer-grade.
We perform the density functional theory (DFT) method to investigate the structural stability, the electronic structure, and the charge density distribution and transfer of the eight boron-doped (4, 0) single-walled carbon nanotube (B-doped SWCNT) systems. The eight B-doped (4, 0) SWCNT systems are distinguished by the number of B atoms substituting C atoms in a (4, 0) SWCNT structure. We find that all B-doped (4, 0) SWCNT structures are formed spontaneously marked by their negative formation energy. Also, all of these new systems have the stable structures. Then, surprisingly, we invent that the substitution doping B atoms retains the electronic properties of (4, 0) SWCNT. This is in contrast to other cases of impurities which alter the electronic properties of the doped structures. In addition, the distribution of charges between boron and carbon in the B-doped (4, 0) SWCNT structures indicates that there are electrostatic attractions between these two types of atoms. It shows that the presence of B atoms can be accepted by a defective (4, 0) SWCNT in order to establish a new integrated B-doped SWCNT structure.