24 September 2021 in Ukrainian Chemistry Journal
Electrochemical impedance spectroscopy was used to study the electrical parameters of graphite-graphene systems with different mass concentrations of graphene. Graphene was synthesized using two methods of plasma arc discharge from aqueous and non-aqueous medium (water and liquid nitrogen) to determine the impact of graphite concentration, water, and heat treatment of graphene on electrical parameters (conductivity and electrostatic capacity) of the graphite-graphene mixture. The average values of active resistance and electrostatic capacity of these systems are obtained. The optimal ratio of components with high capacitance and conductivity, which was 1: 1. The influence of heat treatment adsorbed on the graphene surface of the water and mass fraction of graphite on the change of electrical parameters of the system is shown. Comparison of the values of capacity and active resistance of the samples showed that the presence of water in graphene reduces the average values of capacity relative to graphene without water by 10 times and symbatically increases the active resistance at a mass ratio of graphene to graphite 1: 3, and at a ratio of 1: 1 values are proportional. Comparison of resistance, capacitance, and charge distribution calculations in a graphite-graphene mixture in the frequency range 10–2 ÷ 103 Hz established the effect of heat treatment on increasing the values of capacitance and active resistance. Heat treatment at 2500C of graphene, synthesized from an aqueous medium, leads to an increase in the values of capacitance and conductivity, which occurs due to a different distribution of charges on the surface. Analysis of charge distribution maps shows that water adsorbed on the surface of graphene in the presence of a significant amount of graphite can be a factor in interfering with the distribution of charge carriers and significantly reduce the conductivity and electrostatic capacity of the system.
7 April 2020 in Ukrainian Chemistry Journal
In article was established the conditions for measuring thermal diffusion and thermoelectric effects in non-isothermal elements with composite electrodes of powdered iron and carbon in the alkaline electrolytes using electrochemical impedance spectroscopy. By the modeling of the impedance spectra of these systems has been established the most advantageous equivalent model scheme, which confirms that the external resistance has several components: the resistance of the electrolyte, the resistance of the capacity of the double electric layer and the resistance of thermal diffusion, which forms the dispersion of the capacity. By the calculations of the capacity and the dispersion of the capacity in the low- and high-frequency measurement range have been shown the effect of the concentration of composition components on the formation of the additional heat capacity, which creates the preconditions for realizing of the thermal electrical effects. Increasing of a concentration of the iron leads to the increase of the number of oxide (semiconductor) structures that increase the additional heat capacity. Such heat capacity induces electrical capacity and its dispersion. That is, it creates the preconditions for the occurrence of thermoelectric effects, especially Sore effects in the non-isothermal element. This work was realized due the projects of the Purpose Program for Basic Research of the Chemistry Department of NAS of Ukraine "Basic Research in Priority Areas of Chemistry" P - 1 - 17 DR 0117U000856 and "Strategy of creation of new heat-energy systems based on iron and its compounds, sulfur and oxygen" No. 0117U0008.
16 November 2020 in Ukrainian Chemistry Journal
Using scanning electron microscopy, X-ray photoelectron spectroscopy, and Raman scattering we studied the charge state of matrix and doping element atoms on the surface, morphology, and defects in the structure of graphene-like materials synthesized by plasma-arc discharge in liquid nitrogen.
24 March 2023 in Ukrainian Chemistry Journal
The possibility of formation of an active interphase on iron particles in C/PVDF has been dictated by the thermochemical reactions of iron and iron oxides in the presence of carbon. The composition with polyvinylidene fluoride (PVDF) changed the redox activity of iron particles and decreased pure iron (Fe0) amount by 0,24 wt. %. The surface properties of various compositions have been characterized by scanning electron microscopy with the analytical mode for determining the relationship between the microstructure and local thermal reactions on the iron particle surface. A relationship between the surface composition, morphology and electrochemical behavior of the Fe/C/PVDF electrodes has been found. Electric current affects the surface morphology and changes it from a mosaic structure to a monolith in atmosphere oxygen. The electrochemical properties of Fe/C/PVDF electrodes have been tested using cyclic voltammetry (CVA). The long air contact (for more than 3 hours) during electrochemical cycling changes the surface structure in the direction of decreasing crystallinity. The Fe/C/PVDF electrode can be charge in neutral solutions (pH ~7).
26 August 2022 in Ukrainian Chemistry Journal
A literature analysis of sources on synthesis methods and their influence on the structural-morphological, physico-chemical, and electrochemical properties of graphene and graphene-like structures was carried out. It was established that these properties have a clear dependence on the synthesis method, starting materials, and the composition of the synthesis medium. The main ways of changing graphene's structural-morphological, physico-chemical and electrical properties are changes in the synthesis method and conditions that affect the formation of σ-bonds and π-bonds. The presence of these bonds regulates the number of graphene layers and the formation of van der Waals interactions between them, as well as the formation of edge structural defects responsible for electrokinetic and catalytic properties. Changing the gas medium to a liquid one greatly simplifies the synthesis of graphene. Still, in the case of a liquid nitrogen medium, simultaneously with a 2-dimensional structure, it is possible to form 3-dimensional particles up to tens of nanometers in size. Aqueous medium and plasma-arc synthesis methods are the most attractive for obtaining materials with electron-donor conductivity, which have attractive electrochemical and catalytic properties for use in chemical current sources and fuel cells. Using an aqueous environment requires mandatory further heat treatment at temperatures above 250 0C to separate chemisorbed water from the structure, which complicates the synthesis procedure. The advantage of the plasma-arc method for the synthesis of graphene and other carbon nanostructures is its ability to shorten the stages of the synthesis of graphene, the possibility of modifying them directly during the synthesis process by changing the environment, easy management, and obtaining a clean final product. In the modern practice, this method is limited to obtaining coatings on a solid carrier.
25 May 2023 in Ukrainian Chemistry Journal
The impact of the nature of electrically conductive graphite and graphene admixtures in spinel LiMn2O4 with different degrees of dispersion, composition and morphology on the surface element distribution and the cycling ability under current loads from 0.5 to 8 C of composite cathode materials based on such spinels have been studied by the methods of electron microscopy, X-ray spectrometry, the BET method and galvanostatic-potentiostatic cycling. The specific surface of graphene structures was studied, which was 23 m2/g for G-N and 27.7 m2/g for G-H2O, and the porosity was about 100 nm for the above samples. It was established that the degree of dispersion of spinel affects not only the morphology of the surface of the electrodes, but also the distribution of elements, primarily manganese and oxygen, which take part in electrode redox reactions, as well as the content of the carbon component. Using the elemental analysis of the component composition of the surface, the ratio of manganese to oxygen was calculated, and it was shown that in samples with graphite, manganese is in a more reduced state, and the maximum oxidized state of manganese is observed in samples with graphene, which was synthesized from an aqueous medium. In the case of finely dispersed spinel, the dependence of the carbon content and the ratio of manganese to oxygen on the surface has an antibate character relative to samples with coarsely dispersed spinel and correlates with the number of mesopores on the surface. The dependence of the degree of dispersion and the oxidation state of manganese is in good agreement with the dependence of specific capacity on the discharge current density for composite electrodes. In XDM spinel with graphene synthesized from an aqueous medium, the obtained capacitive characteristics exceed the other characteristics of the materials by 20%. It has been experimentally proven that by changing the nature of the impurity and the degree of dispersion of the spinel, it is possible to adjust the capacitive properties and resistance to current loads of composite electrodes.