22 September 2023 in IEEE Journal of Microwaves
This article presents a set of measured benchmarks for the noise and gain performance of six different millimeter-wave (mm-wave) gallium nitride (GaN) high electron mobility transistor (HEMT) technologies fabricated at four different foundries in the United States. Measurements of the GaN transistors were collected on two independent noise parameter (NP) systems from 8–50 GHz and 75–110 GHz. The resulting raw NPs were stitched together to yield ultra broadband 8–110 GHz smoothed NPs. Several comparisons and summaries of the minimum noise figure and associated gain are reported for the six different GaN technologies. This work seeks to provide an initial database for noise and gain of GaN HEMTs at mm-wave frequencies to quantify progress on technology in the future.
24 October 2013 in Journal of Micromechanics and Microengineering
We report microfabricated toroidal inductors with nanolaminated ferromagnetic metallic cores for chip-scale, high-power switching converters. The fabrication process of the toroidal inductor is based on individual manufacturing of partial windings (i.e. bottom and vertical conductors) and nanolaminated magnetic core, and integrating them by means of a drop-in approach. The nanolaminated ferromagnetic metallic cores presented in this paper consist of many multilayers of electrodeposited CoNiFe films, each layer with sub-micron thickness, with a total core thickness exceeding tens of microns. The beneficial magnetic properties (i.e. high saturation flux density and low coercivity) of CoNiFe alloys are well suited for chip-scale inductors as they achieve both large energy storage capacity as well as minimized volumetric core losses at high operating frequencies due to their nanolaminated structure. A drop-in integration approach, introduced to combine the microfabricated toroidal inductor windings with the magnetic cores, allows ease of integration. An advantage of this hybrid approach over monolithic fabrication in this application is the potential use of a wide variety of core materials, both microfabricated and bulk-fabricated, and which may or may not ultimately be CMOS-compatible. Exploiting this drop-in approach, 30-turn- and 50-turn-toroidal inductors integrated with nanolaminated CoNiFe cores, having 10 mm outer diameter and 1 mm thickness, have been successfully developed. Both types of inductors exhibit inductances higher than 1 µH at frequencies up to tens of MHz, showing ten times the inductance of an air core device with the same nominal geometry. The peak quality factor of the 30-turn-toroidal inductor reaches 18 at 1 MHz.
25 September 2020 in IEEE Microwave and Wireless Components Letters
Heterogeneous integration of IC chiplets into systems on a chip (SoC) is further revolutionizing the semiconductor industry. This letter introduces a metal embedded chiplet assembly for microwave integrated circuit (MECAMIC) technology that uses high-scaled GaN HEMT chiplets. MECAMIC relies on the cointegration of transistor chiplets with passive interposers using an embedding backside metal process. We report the development of standardized 40-nm AlGaN/GaN HEMT chiplets to rapidly prototype GaN circuits up to W-band by combining advances in e-beam gate processes and massively parallel singulation techniques. GaN chiplets with f T > 110 GHz and I max > 1.3 A/mm were fabricated in yielded quantities exceeding 50000 per 4" wafer. Simulation and experimental results of single-stage MECAMIC circuits with 4 μm × 37.5 μm device chiplets demonstrated 6.8-dB gain at 77 GHz. The MECAMIC technology not only optimizes the GaN wafer utilization but also provides the ability to incorporate other technologies, offering unique design flexibility at millimeter wave.
1 February 2021 in Microelectronic Engineering
12 August 2021 in IEEE Transactions on Magnetics
This work introduces a material and method for high-volume, low-temperature, screen printing of self-biased magnetic films made from a composite of M-type strontium ferrite SrFe 12 O 19 (SrM) particles and polydimethylsiloxane (PDMS). The magnetic particles are aligned under a dc magnetic field, while the PDMS is cured at 75 °C, making this fabrication process compatible with semiconductor and printed-circuit-board substrates. Aligned composites with estimated SrM particle volume percentages of 14 vol.%, 20 vol.%, and 27 vol.% are fabricated, as well as an unaligned 14 vol.% composite for comparison. X-ray diffraction (XRD) and scanning electron microscopy (SEM) are used to examine the structure and composition of the composites. Furthermore, vibrating sample magnetometer and ferromagnetic resonance (FMR) measurements are performed to determine their dc and ac magnetic properties. Results show that the aligned composites have magnetic textures between 1.47 and 1.95, crystalline anisotropies between 1860 and 1960 kA/m, FMR frequencies of 45.5–45.9 GHz, and FMR linewidths between 3400 and 3500 Oe, indicating the potential for these materials in self-biased, non-reciprocal device applications. The analysis identifies that increased particle loading and better particle alignment may further improve these films by decreasing the linewidth.
28 July 2020 in IEEE Transactions on Components, Packaging and Manufacturing Technology
This letter provides an overview of the Metal Embedded Chiplet Assembly for Microwave Integrated Circuits (MECAMIC) technology. MECAMIC is a 2.5D wafer-level packaging approach that provides seamless heterogeneous integration capabilities of compound semiconductor transistors (e.g., GaN HEMTs) with passive components and interconnects using a backside metal embedding process. The chiplets are embedded in through-interposer cavities and the backside metallization locks the chiplets into position while providing DC and RF ground for the high-frequency circuits. With this hybrid manufacturing approach, high-performance RF ICs can 1) be designed using the best transistor technology for the function, 2) be fabricated in short cycle times through hybrid manufacturing, and 3) compete performance-wise with monolithic circuits. We demonstrated an X-band power amplifier circuit realized in MECAMIC with a saturated output power of 31 dB and a peak power added efficiency of 54%, which compared favorably to its monolithic GaN MMIC counterpart. The MECAMIC process cycle time was 4.5X faster than the monolithic process.