28 January 2021 in IEEE Sensors Journal
This paper presents multifunctional electronic skin (e-Skin) with a stack of pressure and temperature sensors arrays. The pressure sensor layer comprises of an 8x 8 array of capacitive sensors using soft elastomers as the dielectric medium and the temperature sensing layer comprises of 4 x4 array of conductive polymers based resistive sensors. Three variants of capacitive pressure sensors were developed using two different dielectric materials (PDMS and Ecoflex) to find the best combination of performance and softness. The Ecoflex-based pressure sensor showed high sensitivity (~4.11 kPa −1 ) at a low-pressure regime (< 1 kPa) and the 7.5:1 PDMS based pressure sensor showed high sensitivity (~2.32 kPa −1 ) in the high-pressure regime (>1 kPa). Two variants of temperature sensors were fabricated using CNT and CNT & PEDOT:PSS conducting polymer composite and their performance compared. Finally, a highly sensitive CNT+PEDOT:PSS based resistive temperature sensors layer was integrated on top of 7.5:1 PDMS based capacitive pressure sensors layer to realize the e-Skin prototype. The developed e-Skin is capable of sensing pressures greater than 10 kPa with a high sensitivity of ~2.32 kPa −1 at 1 kPa and temperatures with the sensitivity of ~0.64 (%)/(°C) up to 80°C, thus demonstrating high potential for use in robotics and touch based interactive systems.
1 August 2011 in Powder Technology
NSN. Clament Sagaya Selvam
6 October 2015 in Advanced Materials
13 January 2022 in IEEE Sensors Journal
Highly sensitive capacitive pressure sensors with wide detection range are needed for applications such as human-machine interfaces, electronic skin in robotics, and health monitoring. However, it is challenging to achieve high sensitivity and wide detection range at the same time. Herein, we present an innovative approach to obtain a highly sensitive capacitive pressure sensor by introducing a zinc oxide nanowire (ZnO NW) interlayer at the polydimethylsiloxane (PDMS)/electrodes interface in the conventional metal-insulator-metal architecture. The ZnO NW interlayer significantly enhanced the performance with ~7 times higher sensitivity (from 0.81%kPa −1 to 5.6452%kPa −1 at a low-pressure range (0-10 kPa)) with respect to conventional capacitive sensors having PDMS only as the dielectric. The improvement in sensitivity is attributed to the enhanced charge separation and electric dipole generation due to the displacement of Zn + and O − under applied pressure. Further, the orientation of ZnO NWs and their placement between the electrodes were investigated which includes either vertical or horizontal NWs near the electrodes, placing a third ZnO NW interlayer in the middle of dielectric PDMS and introducing an air gap between the ZnO NWs/electrode. Among various combinations, the introduction of air gap between the electrode and ZnO NW interlayer revealed a significant improvement in the device performance with ~50 times enhancement at a low-pressure range (0-10 kPa) and more than 200 times increase at a high-pressure range (10-200 kPa), in comparison with the conventional PDMS-based pressure sensor.
23 November 2016 in Scientific Reports
Flexible In-Ga-ZnO (IGZO) thin film transistor (TFT) on a polyimide substrate is produced by employing a thermally stable SA7 organic material as the multi-functional barrier and dielectric layers. The IGZO channel layer was sputtered at Ar:O2 gas flow rate of 100:1 sccm and the fabricated TFT exhibited excellent transistor performances with a mobility of 15.67 cm2/Vs, a threshold voltage of 6.4 V and an on/off current ratio of 4.5 × 105. Further, high mechanical stability was achieved by the use of organic/inorganic stacking of dielectric and channel layers. Thus, the IGZO transistor endured unprecedented bending strain up to 3.33% at a bending radius of 1.5 mm with no significant degradation in transistor performances along with a superior reliability up to 1000 cycles.