7 March 2022 in IEEE Transactions on Power Electronics
The dead-time between the switches in the upper and the lower bridge of voltage source PWM converters produces input current distortion, called as dead-time distortion. The dead-time distortion can be compensated by trapezoidal voltage. The conventional trapezoidal voltage compensation method (TVCM) only controls the angle of the trapezoidal voltage. By the control of the angle and amplitude of the trapezoidal voltage simultaneously, an improved TVCM is proposed to further reduce the dead-time distortion. The experimental results are provided to verify the analysis results.
25 August 2020 in IEEE Transactions on Power Electronics
In this letter, a digital control strategy with a simple transfer matrix between three-phase ac input voltages and DC output voltage is proposed for three-phase buck rectifier (3ph-BR) under unbalanced ac input conditions. The proposed digital control strategy can eliminate both the odd harmonics of the ac input currents and the even harmonics of the output voltage ripple under unbalanced ac input conditions. Compared with the state-of-the art control strategies, the proposed control strategy does not require the extraction of the positive sequence voltage and the negative sequence voltage, thus three-phase lock loop (PLL) and complex calculation are not required. The proposed control strategy is essentially an input voltage feedforward control, which is independent of the loop bandwidth of the feedback system. Therefore, the processing speed of the digital processor is no longer the critical factor for the 3ph-BR under the unbalanced ac input conditions. The proposed control strategy makes it possible to utilize low cost and small size digital processor. Experimental prototype of a 1.5kW 3ph-BR with the proposed control strategy is built to verify the analysis results.
2 November 2020 in IEEE Transactions on Power Electronics
For high density three-phase buck rectifier (3ph-BR), such as a standard full-brick size 3ph-BR, there exist obvious parasitic capacitances distributed between its dc-link output and the system ground, which lead to the low frequency distortion of input currents, and thus seriously deteriorates the input current total harmonics distortion (THD). The effect of the distributed parasitic capacitances becomes more obvious for the 3ph-BR under light load conditions. To improve the input current quality of the high density 3ph-BR, a modified 3ph-BR is introduced in this paper. The modified 3ph-BR has one low frequency current path which realizes power transfer from ac input to dc output, and two high frequency current paths which provide low impedance path for high frequency currents. The high frequency current caused by the parasitic capacitance distributed between the dc-link output and the system ground circulates internally, rather than flows to the ac input side. Thus, input current THD of the modified 3ph-BR can be reduced. A 1kW experimental prototype of the modified 3ph-BR with 200 kHz switching frequency and standard full-brick size is built to verify the analysis results.
6 December 2020 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Handing stability and ride comfort, basic indexes to evaluate vehicle performance, usually cannot be guaranteed simultaneously. Given the contradiction between the two indexes, a new type of suspension – balanced suspension, has attracted wide attentions for years. Balanced suspensions are a device that converts the movement of a wheel into force at the other wheels through a mechanical or hydraulic structure, which might improve ride comfort/handling stability while maintaining the handling stability/ride comfort. As the hydraulically interconnected suspension and hydro-pneumatic suspension show disadvantages of high cost and high installation space requirement, a specific balanced suspension which is connected through a mechanical structure is presented and thoroughly analyzed in this paper. The balanced suspension connects the front and rear suspension motion of the vehicle by means of the lever mechanical connection structure to obtain the comprehensive performance of enhanced vehicle’s ride comfort and handling stability. The half-vehicle mathematical model for ride comfort and the multi-body dynamics model for handling stability are established for the comparison and analysis of the dynamic performance of vehicle when the balanced suspension on and off. In addition, experimental tests of the modified vehicle prototypes when the balanced suspension on and off on the ride comfort and handling stability are conducted. Similar with the simulation results, experimental tests show that the handling stability is nearly unchanged while the ride comfort improves about 15.9% when the balanced suspension is on.
2 June 2020 in IEEE Transactions on Power Electronics
In this paper, sector update delay (SUD) of digital control three-phase six-switch (3ph-6s) buck power factor correction (PFC) converter is analyzed. SUD of 3ph-6s buck PFC converter results in increase of switching loss and input current distortion at the transition from even sector to odd sector. For applications when ac input frequency is 47-63Hz, the effect of SUD is relatively small and SUD is usually ignored. However, for applications of high ac input frequency, e.g. 360-800Hz, SUD of 3ph-6s buck PFC converter seriously affects its efficiency and input current total harmonics distortion (THD). In order to suppress the effect of SUD and to improve input current THD and efficiency of 3ph-6s buck PFC converter over wide ac input frequency, a time delay compensation method has been proposed in this paper. The effect of SUD is verified by a 1.5-kW prototype with a low-cost microcontroller. Experimental results show that lower input current THD and higher efficiency over wide ac input frequency have been achieved by the proposed compensation method.
30 October 2020 in IEEE Transactions on Power Electronics
An improved three-phase buck rectifier (3ph-BR) with low voltage stress on switching devices is proposed in this letter. In the conventional 3ph-BR, the voltage stress on MOSFETs is higher than the amplitude of input phase voltage. However, in the proposed 3ph-BR, the voltage stress on MOSFETs is lower than the amplitude of input phase voltage, which results in reduction of voltage stress on MOSFETs. Therefore, the cost-efficient and low voltage rating MOSFETs with low on-resistance can be utilized, which makes the proposed 3ph-BR suitable for applications that require high-efficiency and high-density. A 1.5 kW experimental prototype of the proposed rectifier is built to verify the analysis results.