11 June 2021 in IEEE Electron Device Letters
Despite tremendous interests in ferroelectric field-effect transistors (FEFETs) for embedded, data-centric applications, the fundamental trade-offs between memory window (MW) and write voltage to optimize performance remains poorly understood. To that end, we fabricated ferroelectric (FE) ZrO2 based, p-type FEFETs and studied the impacts of FE and the interfacial oxide layer (IL) thicknesses (tFE and tIL, respectively) on device performance. We observe that a decrease of tFE and tIL reduces not only write voltages for erasing and programming, but also the memory window. A quantitative analysis of these results offers the following insights and guidelines for FEFET design: to decrease write voltages, all of tFE, tIL and coercive field of FE needs to decrease, and to compensate for the subsequent decrease in MW, the polarization of the FE needs to be increased - notwithstanding the fact that the reliability implications of the magnitude of FE polarization still need to be understood.
1 January 2023 in Journal of Vacuum Science & Technology B
In this work, hafnium zirconium oxide (HZO)-based 100 × 100 nm2 ferroelectric tunnel junction (FTJ) devices were implemented on a 300 mm wafer platform, using a baseline 65 nm CMOS process technology. FTJs consisting of TiN/HZO/TiN were integrated in between metal 1 (M1) and via 1 (V1) layers. Cross-sectional transmission electron microscopy and energy dispersive x-ray spectroscopy analysis confirmed the targeted thickness and composition of the FTJ film stack, while grazing incidence, in-plane x-ray diffraction analysis demonstrated the presence of orthorhombic phase Pca21 responsible for ferroelectric polarization observed in HZO films. Current measurement, as a function of voltage for both up- and down-polarization states, yielded a tunneling electroresistance (TER) ratio of 2.28. The device TER ratio and endurance behavior were further optimized by insertion of thin Al2O3 tunnel barrier layer between the bottom electrode (TiN) and ferroelectric switching layer (HZO) by tuning the band offset between HZO and TiN, facilitating on-state tunneling conduction and creating an additional barrier layer in off-state current conduction path. Investigation of current transport mechanism showed that the current in these FTJ devices is dominated by direct tunneling at low electric field (E < 0.4 MV/cm) and by Fowler–Nordheim (F–N) tunneling at high electric field (E > 0.4 MV/cm). The modified FTJ device stack (TiN/Al2O3/HZO/TiN) demonstrated an enhanced TER ratio of ∼5 (2.2× improvement) and endurance up to 106 switching cycles. Write voltage and pulse width dependent trade-off characteristics between TER ratio and maximum endurance cycles (Nc) were established that enabled optimal balance of FTJ switching metrics. The FTJ memory cells also showed multi-level-cell characteristics, i.e., 2 bits/cell storage capability. Based on full 300 mm wafer statistics, a switching yield of >80% was achieved for fabricated FTJ devices demonstrating robustness of fabrication and programming approach used for FTJ performance optimization. The realization of CMOS-compatible nanoscale FTJ devices on 300 mm wafer platform demonstrates the promising potential of high-volume large-scale industrial implementation of FTJ devices for various nonvolatile memory applications.
24 January 2022 in IEEE Transactions on Electron Devices
While the theoretical maximum of the memory window $Δ V_{t}$ in a ferroelectric field-effect transistor (FEFET) is $2E_Ct_F$ , $E_C$ and $t_F$ being coercive field and FE thickness, respectively, experimentally $Δ V_{t}$ is observed to be much less than that, even in the case of complete polarization switching in the ferroelectric layer. This occurs because trapped charges in the gate oxide stack partially or completely screen the ferroelectric polarization, only a fraction of which gets ``electrostatically'' reflected in the semiconductor channel. In this article, we provide a generalized experimental framework to quantify the efficiency of practical FEFETs in converting the switched ferroelectric polarization into the memory window. To that end, we propose three efficiency metrics: 1) switched ferroelectric polarization $Δ P_F$ to memory window conversion ratio, $η_{MW}=Δ V_{t}/Δ P_F$ ; 2) switched ferroelectric polarization to the semiconductor charge ( $Δ Q_S$ ) conversion efficiency or the charge conversion efficiency $η_{c}=Δ Q_s/Δ P_F$ ; and 3) the ratio of memory window to the width of polarization versus gate voltage hysteresis characteristics ( $Δ V_P$ ) or the voltage conversation efficiency $η_V=Δ V_{t}/Δ V_P$ . We measure and compare these efficiency metrics in n-type and p-type FEFETs, fabricated in different facilities by different groups. In all the cases, we find that the maximum values of memory window efficiency $(η_{MW})_{max}$ , charge conversion efficiency $(η_{c}$ ) $_{max}$ , and voltage conversion efficiency ( $η_{V}$ ) $_{max}$ are in the range: 2.5-5.5 Vm²/C, 4%-10%, and 5%-20%, respectively.
1 October 2021 in ECS Transactions
7 May 2021 in ECS Transactions
We evaluated atomic layer deposition (ALD) for the growth of HfO2 for integration in resistive RAM (ReRAM) test structures on 300mm wafers in order to optimize electrical performance for use as synaptic device elements in analog in-memory computing. The effect of ALD oxidant was evaluated and it was shown that H2O outperformed O3 in terms of better uniformity and lower forming voltage. By utilizing H-based plasma after deposition or inserted as an intermediate step during deposition, we were able to further decrease forming voltage for a fixed dielectric thickness. Reducing deposition temperature to 200°C in conjunction with the H-based plasma treatment resulted in additional reduction in forming voltage. Stable high-resistance switching with analog behavior in scaled BEOL devices was obtained using this HfO2-based ReRAM. Additionally, a tight distribution of forming voltage was obtained ensuring that 99.9999% of devices in a 14nm ReRAM module can be formed below the targeted voltage.
1 October 2024 in Journal of Micro/Nanopatterning, Materials, and Metrology
Non-destructive metrology is critical to enabling process control for current and next-generation three-dimensional (3D) transistor and memory structures.1 3D structures have become necessary due to scaling and performance requirements at advanced process nodes.2,3 Here, we discuss optical scatterometry and X-ray metrology for 3D nanosheet/nanowire (NS/NW) transistors with vertically stacked channels, which are fabricated using selective etching of the silicon–germanium