Kenichi Soga

Kenichi Soga

Auto-generated profile, based on publicly available information

Kenichi Soga

Professor of Civil Engineering, Dept. of Engineering, Univ. of Cambridge, Trumpington St., Cambridge CB2 1PZ, U.K.

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2014 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
KAKeita Abe
Keita Abe
KSKenichi Soga
Kenichi Soga
SBSamila Bandara
Samila Bandara
This paper describes a new formulation of the material point method (MPM) for solving coupled hydromechanical problems of fluid-saturated soil subjected to large deformation. A soil–pore fluid coupled MPM algorithm based on Biot’s mixture theory is proposed for solving hydromechanical interaction problems that include changes in water table location with time. The accuracy of the proposed method is examined by comparing the results of the simulation of a one-dimensional consolidation test with the corresponding analytical solution. A sensitivity analysis of the MPM parameters used in the proposed method is carried out for examining the effect of the number of particles per mesh and mesh size on solution accuracy. For demonstrating the capability of the proposed method, a physical model experiment of a large-scale levee failure by seepage is simulated. The behavior of the levee model with time-dependent changes in water table matches well to the experimental observations. The mechanisms of seepage-induced failure are discussed by examining the pore-water pressures, as well as the effective stresses computed from the simulations.

1 August 2012 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
HMHisham Mohamad
Hisham Mohamad
KSKenichi Soga
Kenichi Soga
PBPeter J. Bennett
Peter J. Bennett
RMRobert J. Mair
Robert J. Mair
CLChi Sharn Lim
Chi Sharn Lim
In this field trial, a new monitoring technique using distributed strain sensing known as Brillouin optical time-domain reflectometry (BOTDR) was introduced to monitor the behavior of bolted-concrete linings of a recently completed tunnel when a second bored tunnel was constructed side by side at a distance less than one tunnel diameter apart. This was done by measuring circumferential strains in 12 rings using optical fiber that was installed using the point-fixing method. The strain distributions around the circumference of the rings show a generally similar profile. Maximum compressive strains measured below the tunnel springline nearest to the excavated tunnel were larger than the maximum tensile strains measured at the tunnel crown, distorting the circular tunnel into an oval/ellipsoid that was about symmetrical to the horizontal axis. Several methods were introduced to compare strain measurements made by BOTDR and diameter changes recorded by tape extensometer. This involves the use of a symmetrical tunnel distortion model and the basic differential equation for a circular arch. The calculated results showed some degree of similarity between the two methods. The analysis highlighted the importance of measuring the axial strain in the tunnel ring and subtracting the axial strain component to calculate the actual deflection of the lining as a result of bending.

1 December 2011 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
HMHisham Mohamad
Hisham Mohamad
KSKenichi Soga
Kenichi Soga
APAdam Pellew
Adam Pellew
PBPeter J. Bennett
Peter J. Bennett
An optical fiber strain-sensing technique, on the basis of Brillouin optical time domain reflectometry (BOTDR), was used to monitor the performance of a secant pile wall subjected to multiple props during construction of an adjacent basement in London. Details of the installation of sensors and data processing are described. Distributed strain profiles were obtained by deriving strain measurements from optical fibers installed on opposite sides of the pile to allow monitoring of both axial and lateral movements along the pile. Methods for analyzing the thermal strain and temperature compensation are also presented. Measurements obtained from the BOTDR were found to be in good agreement with inclinometer data from the adjacent piles. The relative merits of the two different techniques are discussed.

5 February 2016 in Acta Geotechnica
Verified
Journal Article
Open access
PDF file
EFElliot James Fern
Elliot James Fern
KSKenichi Soga
Kenichi Soga
The granular column collapse is a well-established experiment which consists of having a vertical column of granular material on a flat surface and letting it collapse by gravity. Despite its simplicity in execution, the numerical modelling of a column collapse remains challenging. So far, much attention has been dedicated in assessing the ability of various numerical methods in modelling the large deformation and little to the role of the constitutive model on both the triggering mechanism and the flow behaviour. Furthermore, the influence of the initial density, and its associated dilatancy and strength characteristics, have never been included in the analyses. Most past numerical investigations had relied on simple constitutive relations which do not consider the softening behaviours. The aim of this study is to illustrate the influence of the constitutive model on the on-set of failure, the flow behaviour and the deposition profile using the material point method. Three constitutive models were used to simulate the collapse of two granular columns with different geometries and for two densities. The results of the simulations showed that the constitutive model had a twofold influence on the collapse behaviour. It defined the volume of the mobilised mass which spread along the flat surface and controlled the dissipation of its energy. The initial density was found to enhance the failure angle and flow behaviours and was more significant for small columns than for larger ones. The analysis of the potential energy of the mobilised mass explained the existence of two collapse regimes.

1 April 2010 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
KJKaushal Joshi
Kaushal Joshi
CKCedric Kechavarzi
Cedric Kechavarzi
KSKenneth Sutherland
Kenneth Sutherland
MNMan Yin Albert Ng
Man Yin Albert Ng
KSKenichi Soga
Kenichi Soga
PTPaul Tedd
Paul Tedd
Slurry trench cutoff walls, constructed using self-hardening slag-cement-bentonite (Slag-CB), are the most common form of in-ground vertical contaminant barrier in the U.K., Europe, and Japan, and are increasingly being used in the United States. This paper presents a case study of the hydraulic conductivity evaluation of an 11-year-old Slag-CB wall material at a sulfate-contaminated site, using different in situ techniques and laboratory tests. The laboratory results suggest that the hydraulic conductivity of the samples, which vary in age from 4 weeks to 11 years, decreases with time for the first 3 years but then remains constant. The results indicate that the long-term performance of these containment walls is influenced by various parameters such as aging, the type/duration of contaminant exposure, mixing of surrounding soil during construction, and wall depth. Piezocone tests, packer tests, and self-boring permeameter tests were carried out in the field to determine the suitability of different in situ techniques and compare with the laboratory results. The hydraulic conductivity is affected by the type of in situ technique used and the geometric scale of the test section.

24 October 2013 in Journal of Micromechanics and Microengineering
Verified
Journal Article
Closed access
PDF file
YJYu Jia
Yu Jia
JYJize Yan
Jize Yan
KSKenichi Soga
Kenichi Soga
ASASHWIN A. SESHIA
ASHWIN A. SESHIA
Resonant-based vibration harvesters have conventionally relied upon accessing the fundamental mode of directly excited resonance to maximize the conversion efficiency of mechanical-to-electrical power transduction. This paper explores the use of parametric resonance, which unlike the former, the resonant-induced amplitude growth, is not limited by linear damping and wherein can potentially offer higher and broader nonlinear peaks. A numerical model has been constructed to demonstrate the potential improvements over the convention. Despite the promising potential, a damping-dependent initiation threshold amplitude has to be attained prior to accessing this alternative resonant phenomenon. Design approaches have been explored to passively reduce this initiation threshold. Furthermore, three representative MEMS designs were fabricated with both 25 and 10 μm thick device silicon. The devices include electrostatic cantilever-based harvesters, with and without the additional design modification to overcome initiation threshold amplitude. The optimum performance was recorded for the 25 μm thick threshold-aided MEMS prototype with device volume ∼0.147 mm3. When driven at 4.2 ms−2, this prototype demonstrated a peak power output of 10.7 nW at the fundamental mode of resonance and 156 nW at the principal parametric resonance, as well as a 23-fold decrease in initiation threshold over the purely parametric prototype. An approximate doubling of the half-power bandwidth was also observed for the parametrically excited scenario.