Airborne magnetic surveys are common in geosciences. High‐precision surveys are usually performed at a low altitude, draping the topography, using scalar absolute magnetometers and active compensation systems to correct the disturbances generated by the carrier. Another solution is to measure the total magnetic intensity using vector magnetometers, which allows compensation for aircraft fields to be calculated directly, without compensation systems. This study uses data of an industrial airborne survey and of a vector magnetometer survey with a small overlapping area in the Vosges (France) to compare both data sets and shows that both solutions provide results of the same overall precision. This paper also addresses the issue of combining fixed altitude and draped level data sets as well as topographic effect management by proposing an equivalent source interpolator based on a set of simple dipole sources. A synthetic case shows that the equivalent source interpolator allows to compute grids of the magnetic anomaly as well as potential field transforms from a draped data set with an error level a few orders of magnitude lower than could be obtained with minimum curvature, a classically applied interpolator. The interpolator is also tested on a case study in the Vosges massif of which geological interpretation is presented in Bertrand et al. (2020, https://doi.org/10.1029/2019JB017688). The results confirm the observations made on the synthetic case and show that the equivalent source interpolator is more tolerant to navigation errors (altitude) than minimum curvature and allows more rigorous computation of potential field transforms of draped data sets.
19 May 2020 in Journal of Geophysical Research: Solid Earth
In many grabens of the West European Rift System, several drilling projects are targeting fluid conductive faults to produce electricity with geothermal energy. In order to reach the adequate temperatures, the targeted faults are located in the basement rocks or at the basement/cover interface. Unfortunately, the basement rock facies and structural data useful for reservoir modeling are often poorly constrained because of the lack of boreholes deeper than 2,000 m and seismic information on the deep subsurface. With the aim to outline the basement structure in the Upper Rhine Graben, two aeromagnetic surveys were conducted where the basement outcrops in the Northern Vosges, with different flight parameters and types of magnetometers. An interpolator using equivalent sources for gridding these two surveys is described by Gavazzi et al. (2020). Here, we describe the geological interpretation of these surveys. We demonstrate the consistency between the total magnetic field intensity and the outcropping lithological units organized in ENE‐WSW subvertical bands. In detail, three main blocks were delineated, separated by N‐S faults linked to the graben formation and ENE‐WSW‐inherited Hercynian faults. The latter faults, together with more local NE‐SW and NW‐SE faults, compartmentalize the N‐S‐oriented basement rocks. This is relevant for geothermal prospection where the N‐S faults are the main targets because fluid flow through other fault systems is deemed restricted. With a focus on the interface between the Northern Vosges and the Upper Rhine Graben, we also demonstrate considerable segmentation on the main graben boundary faults.
Un diagnostic magnétique a été effectué les 11 et 12 mai 2015 par l’École Observatoire des Sciences de la Terre de Strasbourg, sur la commune d’Étaples. L’objectif était la cartographie magnétique d’un terrain de 1,22 ha, recelant les vestiges d’un ouvrage fortifié, afin de détecter dans le sous-sol la présence ou l’absence de structures anthropiques avant une campagne de sondages archéologiques programmés. Les mesures magnétiques ont été faites avec un système composé de six capteurs espacés...
Ground magnetic surveys are commonly used for imaging near-surface structures in archaeological studies. Usually, surveys are conducted using vertical component gradiometers or scalar gradiometers to produce a vertical pseudo-gradient map. Scalar magnetometers can also be used, albeit less frequently, to produce maps of the total magnetic anomaly. In all these cases, the equipment is pushed or pulled by an operator or carried behind a vehicle. Here we present a third approach made available by the use of three-component fluxgate magnetometers: fast surveys over large areas using a compact lightweight drone flying automatically 1 to 2 m above the ground and high precision surveys acquired by an operator 0,2 to 1 m above the ground. A case study on the gallo-roman site of Oedenburg, located along the Rhine River in its upper valley, illustrates the results that can be obtained with the approach. A comparison with previously acquired pseudo-gradient surveys shows that the presented method allows a faster coverage, a greater resolution for the imaging of short wavelength structures (such as walls) and a better capacity of imaging large wavelength structures (such as pathways, palaeochannels or soil composition variations). As the site is crossed by a high voltage electric power line, a method to suppress the high-amplitude 50 Hz frequency magnetic field is presented.
Magnetic mapping is commonly used in the academic and industrial sectors for a wide variety of objectives. To comply with a broad range of survey designs, the use of unmanned aerial vehicles (UAVs) has become frequent over the recent years. The majority of existing systems involves a magnetic acquisition equipment and its carrier (an UAV in this context) with no -or very few- connections between the two systems. Terremys is conceiving and optimizing UAVs specifically adapted for geophysical magnetic acquisitions together with the appropriate processing tools, and performs magnetic surveying in challenging environments. Terremys’ “Q6” system weights 2.5 kg in air, including UAV & instrumentation, and allows 30 min swarm or individual flights.Rotary-wing UAVs are found to be the most adaptive systems for a wide range of contexts and constraints (extensive range of flights heights even with steep slopes). They offer more flight flexibility than fixed-wing aircrafts. One of the major problems in the use of rotary-wings UAVs for magnetic mapping is the magnetic field generated by the aircraft itself on the measurements. Towing the magnetic sensor 2 to 5 m under the aircraft reduces data positioning accuracy and decreases the performances of the UAV, which can be critical for high-resolution surveys. To overcome these problems, a deployable 1 m long boom is rigidly attached to the UAV. The UAV magnetic signal can be divided between 1-the magnetic field of the whole equipment and 2-a low to high frequency magnetic field mostly originating from the motors. The magnetization of the system is the principal source of magnetic noise. It is modelled and corrected by calibration-compensation processes permitted by the use of three-component fluxgate magnetometers. The time-varying noise depends on the motors rotational speed and is minimized by optimizing the UAV components and characteristics along with the boom’s length.The final set-up is able to acquire magnetic data with a precision of 1 to 5 nT at any height from 1 to 150 m above ground level. The high-precision magnetic measurements are coupled with a centimetric RTK navigation system to allow for high-resolution surveying. The quality of the obtained data is similar to that obtained with ground or aerial surveys with conventional carriers and matches industrial standards. Moreover, Terremys’ systems merge in real-time data from all the aircraft instruments in order to integrate magnetic measurements, positioning information and all the UAV’s flight data (full telemetry) into a unique synchronized data file. This opens up many possibilities in terms of QA/QC, data processing and facilitates on-field workflows.Case studies with diverse designs, flight altitudes and targets are presented to investigate the acquisition performances for different applications, as distinct as network positioning, archaeological prospecting or geological mapping.The full integration of the magnetic sensor to the drone opens the possibility for implementation additional sensors to the system. The adjoining of other magnetic sensors would allow multi-sensors surveying and increases daily productivity. Diverse geophysical sensors can also be added, such as thermal/infrared cameras, spectrometers, radar/SAR.