Aleksandar Vranić

Aleksandar Vranić

Auto-generated profile, based on publicly available information

Aleksandar Vranić

Faculty of Mechanical and Civil Engineering in Kraljevo, University of Kragujevac, Kraljevo 36000, Serbia

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 February 2016 in Fatigue & Fracture of Engineering Materials & Structures
Verified
Journal Article
Closed access
PDF file
Dario CroccoloDario Croccolo
Dario Croccolo
MAM. De Agostinis
M. De Agostinis
SFStefano Fini
Stefano Fini
Giorgio OlmiGiorgio Olmi
Giorgio Olmi
AVA. Vranic
A. Vranic
SĆSnežana Ćirić-Kostić
Snežana Ćirić-Kostić

29 June 2018 in Metals
Verified
Journal Article
Open access
PDF file
Dario CroccoloDario Croccolo
Dario Croccolo
Massimiliano De AgostinisMassimiliano De Agostinis
Massimiliano De Agostinis
SFStefano Fini
Stefano Fini
Giorgio OlmiGiorgio Olmi
Giorgio Olmi
FRFrancesco Robusto
Francesco Robusto
NBNebojša Bogojević
Nebojša Bogojević
The main motivations for this study arise from the need for an assessment of the fatigue performance of DMLS-produced Maraging Steel MS1, when it is used in the “as fabricated” state. The literature indicates a lack of knowledge from this point of view; moreover, the great potentials of the additive process may be more and more incremented, if an easier and cheaper procedure could be used after the building stage. The topic has been tackled experimentally, investigating the impact of heat treatment, machining, and micro-shot-peening on the fatigue strength with respect to the “as built state”. The results indicate that heat treatment may improve the fatigue response, as an effect of the relaxation of the process-induced tensile residual stresses. Machining can also be effective, but it must be followed (not preceded) by shot-peening, to benefit from the compressive residual stress state generated by the latter. Moreover, heat treatment and machining are related by a strong positive interaction, meaning their effects are synergistically magnified when they are applied together. The experimental study has been completed by fractographic as well as micrographic analyses, investigating the impact of the heat treatment on the actual microstructure induced by the stacking process.

1 January 2017 in IMK-14 - Istraživanje i razvoj
Verified
Journal Article
Open access
PDF file
AVA. Vranić
A. Vranić
NBNebojša Bogojević
Nebojša Bogojević
SĆS. Ćirić-Kostić
S. Ćirić-Kostić
DCD. Croccolo
D. Croccolo
GOG. Olmi
G. Olmi
This paper presents some various imperfections that can occur during Direct Metal Laser Sintering (DMLS) and their effects on part quality. Direct Metal Laser Sintering is one of the Additive Manufacturing (AM) technologies that enables fast production of an accurate, functional, complex shape parts and tools, without additional tooling, directly from 3D CAD model. This process is based on layer by layer manufacturing, where the fusion of the metal powder is performed by selective melting with laser beam. The laser beam moves and scans area that correspond to section of the part for the specific layer. In the DMLS the part is built layer by layer, where the process of the melting and solidification occur in small volume in relatively short time. Thanks to this kind of approach, the DMLS has much less limitations than the subtractive methods of part production. However, the production in the layers has some drawbacks, which can have a significantly influence on the part geometry, structural errors and part imperfections. Some of the advantages as well and drawback of the DMLS of metal parts has been presented in this paper.

1 January 2017 in FME Transactions
Verified
Journal Article
Open access
PDF file
SŠSlaviša Šalinić
Slaviša Šalinić
AVAleksandar Vranić
Aleksandar Vranić
NNNikola D. Nešić
Nikola D. Nešić
ATAleksandar M. Tomović
Aleksandar M. Tomović
Kinematics and dynamics of a Cardan-Hooke joint are investigated. Kinematic analysis is based on the kinematic chain rule for angular velocity vectors. Dynamics of the Cardan-Hooke joint is analyzed by means of the Lagrange equations of the second kind. The Cardan-Hooke joint is analysed under varying operating conditions, that is, it is assumed that the input shaft has variable angular velocity. Two cases are considered: (1) the driving yoke plane coincides with the plane of the shafts; (2) the driving yoke plane is normal to the plane of the shafts. An expression for torque transmission in a Cardan-Hooke joint in varying operating conditions was developed. The expression contains terms representing inertia of the shafts and the cross of the Cardan-Hooke joint. Theoretical considerations are accompanied by a numerical example.

1 January 2015 in IMK-14 - Istraživanje i razvoj
Verified
Journal Article
Open access
PDF file
AVAleksandar Vranić
Aleksandar Vranić
SĆSnežana Ćirić-Kostić
Snežana Ćirić-Kostić
The influences of various core configurations and other structural characteristics on vibrations of sandwich panels are discussed in the paper. The presented analysis contributes to efforts to resolve the contradiction between the requests for increased stiffness and reduced mass of mechanical structures. Additive manufacturing (AM) technologies enable manufacturing of complex lattice and cellular structures and design of optimal sandwich structures that satisfy both requests. Effects of each design parameters of a sandwich panel (core shape, wall thickness of plates and core, width of core) can be varied independently of the other parameters, thus contributing to change of modal behaviour of the panel. In this study a FEM calculations are used for determining of natural frequencies and mode shapes of sandwich structures designed for production by selective laser sintering technology. Analyses of the obtained results presents base for optimal design of light-weight structures in automotive, aerospace and naval industries.